struments gave different readings for different trials as follows: nstrument 1| 20 30 40 50 60 70 80 51 49 nstrument 2 | 49 | 49 49 49 | 49 49 49 49 49 nstrument 3 48.01 48.03 49.02 49.01 50.00 48.02 47.09 47.05 47.80 nstrument 4 17.01 17.02 17.09 17.03 17.01 17.03 15.09 19.02 17.00 1. Analyze the accuracy of each one of these instruments and based on your analytics arrange them based on their accuracy. 2. Analyze the precision for each of these instruments and based on your analytics arrange them based on their precession. 3. Analyze the accuracy of each one of these instruments after calibration and based on your analytics decide which one has better accuracy after calibration. 4. Which one is more precise after calibration?

struments gave different readings for different trials as follows: nstrument 1| 20 30 40 50 60 70 80 51 49 nstrument 2 | 49 | 49 49 49 | 49 49 49 49 49 nstrument 3 48.01 48.03 49.02 49.01 50.00 48.02 47.09 47.05 47.80 nstrument 4 17.01 17.02 17.09 17.03 17.01 17.03 15.09 19.02 17.00 1. Analyze the accuracy of each one of these instruments and based on your analytics arrange them based on their accuracy. 2. Analyze the precision for each of these instruments and based on your analytics arrange them based on their precession. 3. Analyze the accuracy of each one of these instruments after calibration and based on your analytics decide which one has better accuracy after calibration. 4. Which one is more precise after calibration?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Explain each circuit below and describe how many seconds everytime it lights https://circuitdigest.com/calculators/555-timer-astable-circuit-calculator use this link to refer to seconds
In this System your primary element is sending 1v - 5v to your controller and our controller is sending 4mA - 20mA to your final Element. 1) The Primary Element is sending 2.8v. Your controller is reading 2.8v. The Controller sends 5.2mA to the Final Element but nothing changes in your Process Variable. What is wrong? Controller Final Element Transmitter Wire 2) The Primary Element is sending 12v. Your controller is reading 12v. The Controller sends 0mA to the Final Element. What is wrong? Controller Final Element Transmitter Wire 3) the Primary Element is sending 3.4v. Your controller is reading 0v. The Control is not making changes when necessary, what is wrong? Controller Final Element Transmitter Wire
The rotary potentiometer widely used to measure the angular displacement. It has maximum angle of 120 degree and the total resistance of 420 ohms with 30V of dc power supply. If so, calculate the output voltage for the angular movement of 315 degree to 380,5 degree. O a. 15.735V O b. 15.375V Oc. 16.735V O d. 16.375V Question 12 The rotary potentiometer widely used to measure the angular displacement. It has maximum angle of 120 degree and the total resistance of 420 ohms with 30OV of dc power supply. The error is 0.75 ohms during the measurement of 60 phms, then calculate % accuracy of the device. O a 98,9%| O6.99 8% O 99 62% Od 93.75%
31.11 here is a WRONG answer, I think the answer should be 30.41 since it need to be subtracted to 0.7 making it 30.41. Kindly solve it"
11. For each circuit below, redraw the circuit in conventional form as we did in the lecture, then state whether the diode is forward-biased or reverse biased. ↓ 12 V (a) +5VO (c) -6 Vo + 15 V (b) + 10 V ok NO (d) - 10 V -8 V ↓
Below shows the circuit diagram of a remote control. Explain the operating concept of this simple circuit diagram and how it works to produce the signal.
i need the answer quickly
If D1, D2 and D3 are removed in the circuit and are replaced by short circuit, determine the PIV rating per diode of the remaining diodes in the circuit. O Di Dz D3 中中平 220 V ka D4 D3 3 DG
The simple diagram of the diode circuit and the negative square wave input are shown in the figure. What will be the output voltage value after the tenth cycle? ( Vi=18V , C1=µF, C2= 47 µF 3.83 V (Approximation will be made by assuming C2 large C1)
I need answer for 4 question
please make sure to find Vo as a function of time as part of the solution.
19. Apply a 0.02 cylindricity on the part below and show the resultant tolerance zone on the produced part below it. 10.1 10.0