Steelrailroad reels 15 m long are laid with at an initial temperature T₁ = 56 °C. Assume a = 11.7 µm/(m-°C) and E = 200 GPa.12. What stress would be induced in the rails in MPa at a final temperature of T₁ = 86 °C, if there were no initial clearance. I

Given Data Length of steel railroad (L) = 15m Initial temperature (Ti) = 56°C Final temperature…

Steel railroad reels 15 m long are laid with at an initial temperature T₁ = 56 °C. Assume a = 11.7 μm/(m-°C) and E = 200 GPa. 12. What stress would be induced in the rails in MPa at a final temperature of T₁ = 86 °C, if there were no initial clearance

Steel railroad reels 15 m long are laid with at an initial temperature T₁ = 56 °C. Assume a = 11.7 μm/(m-°C) and E = 200 GPa. 12. What stress would be induced in the rails in MPa at a final temperature of T₁ = 86 °C, if there were no initial clearance

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: a) Transform the beam into one made entirely of steel. b) The steel channel is used to reinforce…

A: Given Data The maximum moment (M) = 1.2 KN-m Est = 200 GPa Ew = 12 GPa We are asked to evaluate the…

Q: A 16 mm steel bar AB and a 25 mm steel bar BC support a load P = 7,500 N as shown. If E = 200 GPa,…

A: Given data: Diameter of AB steel bar=16 mm Diameter of BC steel bar=25 mm Load=7500 N It is asked…

Q: Determine maximum principal stress

A: Given data : Normal stress in X direction σX=-320 MPa Normal stress in Y direction σY=240 MPa Shear…

Q: The reinforced concrete beam shown is subjected to a positive bend-ing moment of 175 kN·m. Knowing…

A: Following is the given figure: Compute the modular ratio as follows: Substituting the values…

Q: Problem 3 A rod consisting of two cylindrical portions AB and BC is restrained at both ends. Portion…

Q: A bar having a cross-sectional area of 700 mm² is subjected to axial loads at the positions…

Q: A load of 1950N is raised at the end of a steel wire. The minimum diameter of the wire so that…

A: Given data :- Load = 1950 N Stress = 100 N/mm2 Calculate the minimum diameter of the wire

Q: Steel railroad reels 10 m long are laid with a clearance of 3 mm at a temperature of 15°C. Assuming…

Q: hollow steel tube with an inside diameter of 100 mm must carry a tensile load of 400kN. Determine…

Q: A transmission shaft made of steel having ultimate strength 500 MPa and yield strength 320 MP is…

A: Given data : Ultimate strength of steel shaft = 500 MPa Yield Strength = 320 MPa Endurance strength…

Q: 3. Consider the given state of stress 40MPA y +, 10MPA → 70MPA 22.5° a) Determine the principal…

A: As per the bartleby guidelines, i am able to answer three sub-parts at a time so I was answered the…

Q: A 100mm* 40 mm* 20 mm steel block is subjected to a hydrostatic pressure of 10MPa. The Young's…

Q: A hollow steel shaft has outside diameter d and inside diameter d/2. The value of d for the shaft,…

Q: · A 3-m long steel rod has a strain of 1.33 x 10³ m/m when subjected to an axial tensile load of 50…

A: We knowModulus of elasticity is E=StressStrainStress=LoadArea=50,000Nπ4×202=159.155Mpa

Q: A hallow cylinder 2m long, outside diameter 5mm and inside diameter of 3mm ,if the cylinder is…

A: Solution: Length, L=2 m Outer diameter, D=5mm Inside diameter, d=3 mm Load, P=29 kN Modulus of…

Q: A high strength steel band saw of rectangular cross-section of size 20 x 0.8 mm thick runs over…

Q: A homogenous isotropic material of size 20 cm x 20 cm x 20 cm is placed inside a rigid box of…

A: Consider the free body diagram;Given;Young modulus, E=Poisson ratio, v=0.3

Q: 4. The beam shown supports the load shown, determine max flexural stress developed and 200mm the max…

Q: w steel shaft with an outside diameter of 100 mm and a wall thickness of 5 mm is subjected to a pure…

A: TJ=τrτ=TJrτ=5400×1000N-mmπ321004-904(1002)τ=79.9708Nmm2

Q: A solid 11 mm diameter shaft is subjected to an axial load of P-33 kN and a torque of Tacting as…

A: Note: Hi! Thank you for the question as per the honour code, we’ll answer the first question since…

Q: A flat bar of cross section 15 mm by 70 mm elongates 2.59 mm in a length of 1.3 m as the result of…

A: Axial stress is the ratio of load and the areaσ=PAσ=230,000N15×70 mm2σ=219Mpa

Q: 6. Steel railroad rails 10 m long are laid with end-to-end clearance of 3 mm at a temperature of…

Q: Steel railroad rails 10 m long are laid with end-to-end clearance of 3 mm at a temperature of 15°C.…

Q: c) A solid homogeneous truss tie-rod has a diameter of 9. 52 mm and an original length of 1.75 m…

Q: A circular aluminum alloy [E = 70 GPa; a = 22.5 x 10-6/°C; v = 0.33] pipe has an outside diameter of…

A: Given: Modulus of elasticity =E Coefficient of thermal expansion Outside diameter Thickness Length…

Q: A flat annular steel disc of 0.8 m outside diameter and 0.15 m inner diameter is to be shrunk around…

A: Pressure is defined as the force that crosses a “small” boundary in each unit area of that…

Q: Define the below ? Lateral strain is considered – Skempton–Bjerrum method

A: Solution: This is the method in which the settlement occurs in the layer of soil wherepi is…

Q: Steel railroad rails 10m long are laid with a clearance of 3mm at a temperature of 15°C. The modulus…

A: Given data, Length of rail = 10 m Clearance = 3 mm Initial temperature = 15 °C E = 200 GPa Final…

Q: Steel railro ad rails 10 m iong are iaid with end-to-end cle arance of 3 mm at a temperature of…

A: GIVEN- L=10mE=200Gpa=200×103N/mm2α=11.7×10-6/°CInitial Temperature=15°C

Q: What is the ratio of the strain energy in bar X to that in bar Y when the material of the two bars…

A: Given data Find the ratio of strain energy in bar-X and bar-Y.

Q: A solid circular steel column is 3 m long and 0.4 m in diameter. It carries a load of 50 MN. The…

A: Given that , length = 3 m diameter = 0.4 m load P = 50 MN = 50 × 106 N E = 200 Gpa = 20 × 109 pa =…

Q: 5. The aluminum alloy bar has a circular cross section with 20-mm diameter and a shear modulus of 28…

A: We will use shear equation.

Q: A steel hollow pipe about 3m long which has the inside diameter of 15mm and outside diameter of…

A: Given Data : Length of hollow pipe, L=3m Inside diameter, Di = 15 mm Outside diameter, Do = 27 mm…

Q: Consider the compound system consisting of three sections with cross-sectional areas 3A, 2A, and A…

A: The correct answer to the given questions are as under

Concept explainers

Composite Construction

Composite construction is the construction of structures in which two or more materials are used. Regarding structural engineering, composite construction is a construction where two materials are bound together in a technical manner such that both the materials act as a single unit to carry and transfer the load. The motives of composite construction are to increase the structural strength, make structures more aesthetic, and provide a sustainable environment.

Question

Steel
railroad reels 15 m long are laid with at an initial temperature T₁ = 56 °C. Assume a = 11.7 µm/(m-°C) and E = 200 GPa.
12. What stress would be induced in the rails in MPa at a final temperature of T₁ = 86 °C, if there were no initial clearance. I

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

If M=6kip.ft, determine the maximum tensile stress in the beam shown in the figure below
In a steel railroad, the 12 meters long rails are laid with a clearance of 5 mm at a temperature of 20 degrees centigrade. The modulus of elasticity of steel is 200 GPa. a) At what temperature will the rails just touch if the coefficient of linear expansion is 11.7x10^-6/°C.? b) Determine the stress in the rails at 65 °C
E al = 70Gpa E cu = 75 Gpa fınd the max stress in both of tow materials in the picture alümünyum = Al Bakır = cu
a.)Determine the required gap (δ) so that the rails just touch one another when the temperature is increased from Ti = -20 °F and Tf = 80 °F (in inches) b.)Determine the stress in steel rails if the gap is δ = 0.5 in and the temperature is increased from Ti = -20 °F to Tf = 100 °F. (in psi)
A flat annular steel disc of 0.8 m outside diameter and 0.15 m inner diameter is to be shrunk around a solid steel shaft. The shrinking allowance is 1 part per 1000. Neglecting shaft expansion, determine: (a) The stress in the system at standstill. (b) The speed at which the shrink fit will loosen as a result of rotation. Material density is 7800 kg/m³; Poisson's ratio is 0.3; Young's Modulus is 210 GPa; [108.68 MPa: 4300 rpm
Please do fast with explanation
A critical point in a part made of a ductile material is subject to the following state of plane stress: 15ksi, 30 ksi, 15 ksi, Ox,min = -35 ksi, Oy,min = 30 ksi, Txy,min = -15 ksi. Ох,max бу,max Тxy,max %3D There are no stress concentrations. The load line is propositional. The material has a yield strength of Sy = 130 ksi, an ultimate strength of Su = 200 ksi, and a fully corrected endurance limit of Sn : 75 ksi. Calculate the: (a) Static factor of safety using the MSSTF, (b) Static factor of safety using the DETF, (c) Fatigue factor of safety using the Soderberg criterion, (d) Fatigue factor of safety using the Goodman criterion, (e) Fatigue factor of safety using the ASME elliptic criterion.
A steel rod is stretched between two rigid walls and carries a tensile load of 5000N at 20oC . If the allowable stress is not to exceed 130 MPa at -20oC, what is the minimum diameter of the rod? Assume teta=11.7 mueM/moC and E= 200 GPa.
A circular aluminum alloy [E = 70 GPa; a = 22.5 × 10-6/°C; v = 0.33] pipe has an outside diameter of 215 mm, a wall thickness of 12 mm, and a length of 4.3 m. The pipe supports a compressive load of 695 kN. After the temperature of the pipe drops 43°C, determine: (a) the axial deformation of the pipe. (b) the change in diameter of the pipe. Answer: (a) ō = i AD = i mm mm
Railway rail problem.
Steel railroad rails 10 m long are laid with end-to-end clearance of 3 mm at a temperature of 15°C. (a) At what temperature will the rails just come in contact? (b) What stress would be induced in the rails at that temperature if there were no initial clearance? Use a = 11.7 x 106 /°C and E = 200 GPa.