steel pipeline 2”sch 40 (k = 45W/mK) contains saturated steam at 121.1oC. the line is insulated with 25.4 mm asbestos (k = 0.182W/mK). Assuming that the inside temperature of the metal wall is at 121.1oC and the outer surface of the insulation is at 26.7oC, calculate the heat loss for 30.5m of pipe.

steel pipeline 2”sch 40 (k = 45W/mK) contains saturated steam at 121.1oC. the line is insulated with 25.4 mm asbestos (k = 0.182W/mK). Assuming that the inside temperature of the metal wall is at 121.1oC and the outer surface of the insulation is at 26.7oC, calculate the heat loss for 30.5m of pipe.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

if you are unable to answer all parts, please do part 4 and 5. thanks
Based on the picture above, make a schematic and determine the average temperature difference over the entire length of the tube (ATLM). (value 25)
i need the answer quickly
IMPORTANT!!! ONLY ANSWER PART D Parts A, B, and C are solved and the answers are in the picture.
A steel tube having k =46W/m•C has an inside diameter of 3.0 cm and a tube wall thickness of 2 mm is covered with a 3-cm layer of asbestos insulation [k =0.2 WN/m•C]. A fluid flows maintains inside tube surface temperature 223•C while the outside surface insulation temperature is 57 C. Calculate the heat lost by the tube per meter of length and what in the tube-insulator interface temperature?
Industrial pipes For externally insulated pipes, is it necessary to use skids in the region of contact between them and the sleepers?
Problem 6. ART TAT Consider the cylindrical pipe shown in the figure. Heat is being generated in the pipe wall at a rate of R in units of W/m³, and the thermal conductivity of the wall is k, the heat transfer coefficients at the inside and outside of the pipe are h; and ho, respectively. At a given location along the pipe axis, the temperature of the fluid flowing inside of the pipe is Ti and that at the outside is To i. ii. Find the expression for the temperature distribution in the pipe wall. Find the total heat transfer rate from the pipe to both fluids.
silicon carbide (T ≈ 300 K): k = 490 W/m⋅K
a. An air stream passing through a 2-inch (1/6 ft) diameter, thin-walled tube is to be heated by high- pressure steam condensing on the outer surface of the tube at 320 °F. The overall heat transfer coefficient, h between steam and air can be assumed to be 25 Btu/(ft2.hr °F) with the air entering at 100 ft/sec, 10 psia, 40 °F. The air is to be heated to 150 °F. Determine the tube length required. Assuming Rayleigh Line flow, calculate the static pressure change due to heat addition. Also, for the same inlet conditions, calculate the pressure drop due to friction, assuming Fanno flow in the duct with f = 0.018. b. c. d. To obtain an approximation to the overall pressure drop in this heat exchanger, add the two results. Discuss the accuracy of this calculation.
Provide schematic diagram and solutions.
L.1What are the best possible solutions to increase the heat transfer rate of a body.Which material will transfer more heat? Either a material with thermal conductivity ? = 121 or ? = 22 . Justify your answer. Explain the Fouling phenomenon. What is the effect of fouling on heat transfer rate? Which of the following Fins/Heat exchanger will transfer more heat and why? Justify your answer.Flat plate.Circular/pin fins.Triangular fins.
2, The internal diameter of a boiler generating tute is 4in. and the wall thickness is 0.375 in. In operation the external surrace film temperature is 26 Btu/hr . ft².°F, the internal film coefficient is 1700 Btu/hr.ft².°F and a 0.375 in. thickness scale having a conductivity of 0.6 Btu/hr.ft. °F is deposited on the inner surface of the tube. The metal conductivity is 26 Btu/hr.ft. °F, the furnace gas temperature is 2100 °F and the temperature of the water is 500 °F, calculate (a) the overall coefficient of heat transfer for the clean tube, (b) the overall heat transfer coefficient including the effect of the scale, (c) the external tube surface temperature before and after the scale