steel beam ABC is supported at A, B and C. The portion AB is 3m long and carries a central concentrated load of 30kN, and BC is 2m long with a uniformly distributed load o -40kN/m on the complete length. Calculate the slope and deflection at point B, and draw the S.F and B.M. diagrams for the beam. Take EI = 0.6MNm².

steel beam ABC is supported at A, B and C. The portion AB is 3m long and carries a central concentrated load of 30kN, and BC is 2m long with a uniformly distributed load o -40kN/m on the complete length. Calculate the slope and deflection at point B, and draw the S.F and B.M. diagrams for the beam. Take EI = 0.6MNm².

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter9: Deflections Of Beams

Section: Chapter Questions

Problem 9.2.5P: The deflection curve for a cantilever beam AB (sec figure) is given by...

See similar textbooks

Similar questions

A beam of uniform rectangular section 200 mm wide and 300 mm deep is simply supported at its ends. It carries a uniformly distributed load of 9 KN/m run over the entire span of 5 m. if the value of E for the beam material is 1 X 104 N/mm2 , find the slope at the supports and maximum deflection. Give me complete solution based on the given above. Again I need to ask the same question since you gave me a wrong answer before.
Question 4: Use the moment-area method to determine the slope and deflection at point B for the structure shown in Figure 4 where CD k.ft = 108 k.ft and AB kips = 18 kips.(E = 10 000 ksi, IAB = 1 440 in4, IBC = 720 in4)
5. A beam of uniform cross section and rectangular is 50mm broad ,75mm deep and 6m long. It is simply supported at each end and carries a concentrated load of 10kN at midspan (E=200GN/m²) Neglecting the weight of the beam, calculate the radius of curvature between the supports and the deflection at midspan.
For the beam and loading shown, use discontinuity functions to compute: (a) the deflection VA of the beam at A, and (b) the deflection Vmidspan of the beam at midspan (i.e., x = 2.45 m). Assume a constant value of El = 1270 kN-m² for the beam; M₁ = 9 kN-m, wo = 19.8 kN/m, LAB = 1.1 m, LBc = 2.7 m. MA A Answer: (a) VA = (b) Vmid i LAB i Wo B LBC mm. mm.
please translate the following problem descriptions into al diagrammatic representation, solve for/draw the shear force and bending moment diagrams and find the deflection and/or slope as indicated: 3. A 16 ft. long simply supported beam is loaded by a 1 k/ft uniform distributed load for the first 6 ft. and (2) point loads, 3 kips each, at 9 ft. and 12 ft. A Structural No. 1 timber (E = 1,600,000 psi) is specified with nominal dimensions of 6x12. Find the magnitude and location of the maximum deflection.
A 16 ft long, simply supported beam is subjected to a 4 kip/ft uniform distributed load over its length and 18 kip point load at its center. If the beam is made of a W14x30, what is the deflection at the center of the beam in inches? The quiz uses Esteel = 29,000,000 psi. Ignore self-weight.
The beam shown below is subjected to a point load of 10kN, and is supported at both ends by fixed connections. Calculate the deflection at the mid-span of the beam, when El is equal to 9.6x10ºNm². Give your answer in mm to the nearest 2dp. 6m 4m 10KN
3. Calculate the slope and deflection at the 60-kNm couple on the structure shown in the accompanying illustration. Use: a. Moment Area Method, b. Conjugate Beam Method 4 kN/m Fixed Hinge 60 kNm 5 m -5 m 5 m -5m I=1.46 x 10° mm". E=200000MPa Activate Windows so to Settings to activate W ndows.
A cantilever 8m long carries a uniformly distributed load of 12kN/m from midspan to free end. Determine the deflection at the free end, Find the smallest moment of inertia (in x10^6 mm^4) so that its maximum deflection does not exceed the limit of 1/360 of the span. Use E = 70 GPa. Determine the required depth of beam if it is a rectangular section with width-to-depth ratio of 0.5.
Refer to the previous problem. Calculate the resulting maximum positive moment (kN-m). O 77.4 O 96.8 O 54.4 O 108.8 SITUATION. A simply supported beam has a span of 12 m. It carries a total uniformly distributed load of 21.5 kN/m. To prevent excessive deflection, a support is added at midspan. Calculate the reaction (kN) at the added support. O 96.75 O 161.25 80.62 O 48.38 PLS ANSWER ASAP THANKS
8. At what distance a should the bearing supports at A and B be placed so that the deflection at the enter of the shaft is equal to the deflection at its ends? Use MAM. The bearings exert only on the hafts. The flexural rigidity is constant. 9. For this beam example, let's say we are interested in finding the deflections at every key point of the beam (A, C, and E) using the conjugate beam method. 10. Determine the equations of the elastic curve using the coordinates x1 and x3 and specify the slope and deflection at point B. El is constant.
On a formatted bond paper, copy and solve the problem. Show your neat and detailed solution. Use three (3) decimal places for your answers and enclosed it in a box. Compute the deflection and slope at a section 8 ft from the wall for the beam shown in the figure using Double Integration Method. Assume that E = 28 x 103 psi and 1= 30.75 1200 lb in4. A 800 lb/ft -8 ft -8 ft B