L 25 mm dia. 5 kN

Q: A very thick structure is subjected to certain traction boundary conditions on its surface. The…

A: As asked only the first three are solved. φ(x,y)=sinxAx2e-y+Bey

Q: PROBLEM 1 Determine all the member forces of the loaded simple truss, shown on the fig., assuming…

A:

Q: 3 Hydraulic motors which operate in both directions are commonly A) Used in conjunction with a…

A: Given question is based on hydraulic and state of air.

Q: Gear 2 (pinion) runs at 1800 rpm ccw and transmits 3.5 kW to frictionless, idler gear 3. The…

A: Given:- P=3.5kW m=2mm Pressure angle=20° N=1800rpm To find:- g) Torque on gear 4

Q: 1 Legs of a pneumatic system are generally equipped with and work stations receive air which meets…

A: This question is based on the concept of legs of pneumatic system and SUS.

Q: flow by 15", as shown in the fīgure flow are 40 kPa and 263 K. respec

A:

Q: Find the support reactions and joint force of the construction, shown on the figure, if: q3D24 kN/m,…

A:

Q: For number 1 and 2. Use the method of joints to determine the force in each member of the roof truss…

A: As per Bartleby's policy, I can answer only the first question. please resubmit the second question…

Q: 4. Two and one-half pounds of air actuate a cycle composed of the following processes: polytropic…

A:

Q: A perfect gas has a value of R = 319.2 J/kg-K and k = 1.26. If 120 kJ are added to 2.27 kg of this…

A:

Q: te the force in each member of mber is in tension or compression.

A:

Q: 4 2, www www 3 al R.

A: For solution refer below images.

Q: Consider a Carnot vapor refrigeration cycle with Refrigerant 134a as the working fluid. The cycle…

A: Given:Cold region temperature, TC=40oFThe ambinet temperature, TH=90oFFind:Coefficient of…

Q: Answer D

A:

Q: Instructions: Identify the talking components by choosing the most appropriate answer from the…

A: To determine: I directly determine what the speed of a hydraulic actuator is going to be. What am…

Q: Your professor at HTU asked you to explain Archimedes topic to your classmates at one of the classes…

A:

Q: A 1000 kg automobile accelerates from 10 km/hr to 120 km/hr. How much work does this require?

A: Question(4)Given:Mass  Initial Velocity Final Velocity To find:The required Work

Q: A smaller power plant produces 25 kg/s steam at 3 MPa, 600 C in the boiler. It cools the condenser…

A: Given: T2 = 600oC P2 =3000 kpa mass flow rate; m =25kg/s use the mollier chart, at point 2,…

Q: 5. A flanged bolt coupling between two shafts carries 12 bolts in a dismeter of 18-in. The shafts…

A: Flanged bolt coupling,   We can see the figure shows the flanged bolt coupling system. For the…

Q: 1. on-off: 2-way/pressurize-exhaust: 2. pneumatic valve: sub-base mounting/hydraulic valve: 3. hand…

A: Here in this question we have to complete the suggested relationship by choosing the appropriate…

Q: Lukewarm water at 60 °C in a storage tank is being pumped at 300 L/min from the tank. The line from…

A: Water temperature, T=60oCWater flow rate, Q=300 L/min=300*10-360m3/s=0.005 m3/sLength of suction…

Q: Mechatronics Write the Boolean Expression for each of the following Figures: 1. 2. Page | 2

A: 1) A*B, since it is a AND gate

Q: A stick of butter at 35°F measures 1.25 in. x 1.25 in. x 4.65 in. and weighs 4.2 ounces. Find its…

A: (1) According to the given data Volume=1.25inx1.25inx4.65inweight=4.2 ounces=0.2625lb   {…

Q: Locate the centroid (x, y) of each of the following composite area or length. 1. 3 in 3. diameter of…

A:

Q: 1. Draw the Shear and Moment diagrams and determine the maximum shear and maximum Moment. A 7KN-M ²2…

A: Shear force and bending moment diagrams are drawn by the considering the various loads and moments…

Q: A piston/cylinder system filled with water at 70°C has a radius of 0.5 m and an initial piston…

A:

Q: For the stop bracket seen below determine the center of gravity (xbar, ybar, and zbar) A = 12 B =…

A:

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.