ng/19:HupCeX-7fb1 TjKjAnHHIrQ7-ussXeH9Kbx8 lo-gK_PM1@thread.tacv2R SearchWODOGA Vote40000 00BrushesColor ColorEditcolorsEdit withPaint 30ShapesColorsSteam is generated at 4.1O MPa and 440C and condensation occurs at 0.105MPa. Find the thermal efficiency of the cyclthe T-S diagram.Draw the schematic diagram and

Answered: Image /qna-images/answer/2f0a9834-443d-4f43-bc65-8daa79231ed5.jpg

Answered: Steam is generated at 4.10 MPa and 440C…

Steam is generated at 4.10 MPa and 440C and condensation occurs at 0.105 MPa. Find the thermal efficiency of the cycle. Draw the schematic diagram and the T-S diagram.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A turbine is supplied with steam at 25 BAR, 42C and exhaust into a condenser at 55 KPa. Find the thermal efficiency of the cycle. Draw the schematic and T-S diagrams with corresponding labels. (Clear handwritten and step by step solution)
CO2 gas enters the pipe at a flow rate of 2 kg / s, 3 MPa pressure and 500 K temperature. While the CO2 pipe type is flowing, it is cooled down at constant pressure and its temperature drops to 450 K at the pipe outlet. Find the ideal gas using the equation.
19. An electric stove having a rating of 3kW is use to boil a 10Li of tap water (Initially at 20°C and whose density at this temperature is 1020kg/m³). If useful energy is around 72% of the total energy supplied by the stove. Determine how long would it take to vaporized all the water in the pan. c. 3.3hours a. 3.2hours b. 3.4hours d. 3.5hours
sketch these processes with respect to the saturation lines on a single T-s diagram
16. Consider the figure below. An electric stove having a rating of 3kW is use to boil a 6Li of tap water (Initially at 20°C and whose density at this temperature is 1020kg/m). If useful energy is around 62% of the total energy supplied by the stove. Determine how long would it take to vaporized all the water in the pan. determine the total kW-hr used by the electric stove in the given condition.
Show all elements of your design including the design calculations for the problem: When heating up a cold stream (5000 kg/h water) from 40ᵒC to 90ᵒC while cooling down a hot stream (5000 kg/h water) from 110ᵒC to 60ᵒC in AES exchangers, how many shells do you need?
Assuming an adiabatic system, how much energy would be required to completely boil 12 liters of water? Assume RT = 25degC.
A water tube boiler produces 250,000 pounds of steam per hour at 1200 psia and1000°F from feed water entering the boiler at 1500 psia and 360°F. Fuel oil havinga higher heating value of 18,200 Btu/lb is supplied to the burners at the rate of20,700 lb/hr. Furnace volume is 1500 cubic feet. Calculate the equivalentevaporation, lb/hrA. 300,117 B. 300,317 C. 300,517 D. 300,717
b) A proccss plant is requircd to produce 10 MW of clctricity powcr. The stcam is to bc supplicd at a rate of 10 kg/s while it enters the adiabatic turbine at 1 MPa and 500°C. Eventually, the steam exits the turbine at 10 kPa with the 85% quality. Evaluate if the plant can fulfil the demand of the expected power output and justify your answer with relevant calculations.
1. Steam is delivered to an engine at 5.4 MPa and 600°C. Before condensation at 31°C, steam is extracted for feedwater heating at 0.60 MPa. For an ideal cycle, find: (A) Amount of steam extracted (B) Wnet (C) eth
Steam enters the turbine at 10 MN/m2and 450oC. The steam expanded in the turbine down to the condenser pressure of 20 kN/m2. The condensate leaving the condenser is pumped to the boiler pressure directly. The turbine has an isentropic efficiency of 89%, and the mass of steam generated in the boiler is 5 kg/s. Find: Cycle thermal efficiency. Plant power output.Neglect the pump work and draw the cycle on a T – s diagram. Hint: 1 MN/m2= 10 bar
What is the critical pressure of R-134a, in kPa?