A steam power plant is located in an industrial park owned by the BERTSCHenergy Group. This is used to generate electricity and steam.A mass flow of 80 kg /s with a steam content of 77% at a pressure of 0.0075 MPa flows into a condenser of the steam pawer plant. In a colecting basin with avolume of 20 m, the condensate flows together at a temperature of 50*C. it gives off the rest of the heat completely to the environment. The ambienttemperature is a constant 24 *C. ispecific heat capacity of water c= 4.18 ki / (kg K)a) Which heat flow has to be dissipated so that there is saturated liquid at the outlet of the condenser? Enter the result in MW with 2 decimal places.Replytb) Calculate the specific entropy difference of the condensate in the collecting basin and enter it in kl / (kg " K) with 2 decimal placesReplyt

@0.0075 MPa specific enthalpy hf=168.75 hfg=2574.0 hg=2405.3 @ quality of 70% h = 168.75 +…

MW with 2 decimali places. a) Which heat flow has to be dissipated so that there is saturated liquid at the outiet of the condenser? Enter the result i ? Reply b) Calculate the specific entropy difference of the condensate in the collecting basin and enter it in k/ g 0 with 2 decimal places Reply

MW with 2 decimali places. a) Which heat flow has to be dissipated so that there is saturated liquid at the outiet of the condenser? Enter the result i ? Reply b) Calculate the specific entropy difference of the condensate in the collecting basin and enter it in k/ g 0 with 2 decimal places Reply

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A refrigerant 134a of a vapor compression refrigeration system includes a liquid-suction heat exchanger. The heat exchanger cools saturated liquid coming from the condenser from 45 °C to 37 °C with the saturated vapor which comes from the evaporator at -8 °C. Calculate: a.) The COP of the system without heat exchanger. b.) The COP of the system with the heat exchanger. c.) Find the percent increase of performance of the system with the heat exchanger based on the system without heat exchanger. d.) Draw the schematic and P-h diagram of the two set-up.
PLEASE DO THIS TYPEWRITTEN AND COMPLETE IT, I WILL UPVOTE. IF NOT COMPLETE AND TYPEWRITTEN, NO UPVOTE. THANK YOU
A food storage chamber requires a refrigeration system of 15 ton capacity operating at an evaporator temperature of -25.2 deg C and a condenser tempreature of 35.8 deg C. Refrigerant (R-717) is used and the system operates under saturated conditions. Determine: a.) C.O.P. b.) Refrigerant flow rate c.) Rate of heat flow removed by condense
An accumulator tank has a capacity of 20MWh. The flow temperature is 110 ° C and the return is 40 ° Cfor the district heating network.a) What is the volume of the accumulator tank when it is full (m³)?
The air entering a compressor with a pressure ratio of 10 at 100kPa at 27°C leaves at 600K. It enters the turbine at a temperature of 1300 K and exits at a temperature of 800 K. Since the power of the gas turbine is 10 MW, a) Draw the T-s diagram of the cycle b) Find the amount of fluid circulating in the installation. c) Find the adiabatic efficiencies of the gas turbine and the compressor. d) Find net work Note. Assume that the specific heat of heating of the air is constant. cp=1 kj/kgC cv=07181 kj/kgC
A diesel engine compresses air whose temperature is 27°C and pressure is 95 kPa. At the end of the heat treatment the pressure in the cylinder becomes 7.2 MPa and the temperature is 1900°C. Calculate : a) compression ratio of the engine b) Cutoff ratio c) Thermal efficiency of the engine d) Average effective pressure
Please find the highest thermal efficiency possible, while remaining within the boundaries. What is required: -Power produced must be at least 60 Mega Watts -Thermal efficiency must be greater than 36% -Back-work ratio must be smaller than 48% Assume: -air is the working fluid -specific heats vary with temperature (use table A-17) -Compressor inlet is at 1atm and 300k -the combustion process is isobaric and is modeled as a heat exchanger -Turbine exhaust is the same pressure as compressor inlet Compressor specifics: -Max volume flow rate (m^3/h) = 600,000 -Max outlet pressure (atm) = 12 -Isentropic efficiency = 90% Combustion chamber and gas tubine specifics (Note these come as a set) -Max pressure = 16.7 atm -Max temp = 1500 (celcius) -Turbine isentropic efficiency = 92% -Max heat rate = 230MW
1. A standard vapor compression refrigeration system uses Ammonia as refrigerant. The Ammonia leaves the evaporator at – 20 degree Centigrade and the condenser pressure is 1200 kPa. The flow rate is 30 kg/min. Determine a) the tons of refrigeration b) the power required c) the COP.
At 10kPa pressure and dryness degree x=0.90, the steam coming out of the turbine goes to the pump with adiabatic efficiency of 0.85 after condensing in the condenser. The pump sends the condensed water to the steam boiler with a working pressure of 8MPa. a) Find the h.T values of the inlet points of the condenser, pump and boiler b) Since the flow rate of the condensed water is 9000 kg/h, find the load of the condenser c) Find the power of the pump
Find the thermal efficiency of the system in percentage to 2.d.p.
In a condenser containing air and water, the air pressure is 13 kPa abs. what is the gage pressure in Kpa at a point 1.24 m below the water surface? a. 100.49 kPa b. 35.16 Kpa c. 126.49 Kpa d. -58.16 kPa e. -76.16 kPa