Steam exiting the turbine of a steam power plant at 90°C is to be condensed in a large condenser by cooling water flowing through AISI 302 stainless steel pipes of inner diameter 20 mm and outer diameter 25 mm at an average temperature of 30°C. The heat transfer coefficients are 1000 W/m²K on the steam side and 80 W/m2K on the water side. Determine the length of the tube required to condense steam at a rate of 100 kg/hr. Steam, 100°F 120 lbm/h Liquid water Cooling water

Steam exiting the turbine of a steam power plant at 90°C is to be condensed in a large condenser by cooling water flowing through AISI 302 stainless steel pipes of inner diameter 20 mm and outer diameter 25 mm at an average temperature of 30°C. The heat transfer coefficients are 1000 W/m²K on the steam side and 80 W/m2K on the water side. Determine the length of the tube required to condense steam at a rate of 100 kg/hr. Steam, 100°F 120 lbm/h Liquid water Cooling water

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Steam condenses at 100°C on the outer surface of a pipe with a thermal conductivity of 180 J/ms°C. The surface heat transfer coefficient of the water flowing in the pipe is 4000 J/m²s°C, and the heat transfer coefficient created by the steam condensing outside is 10000 J/m²s°C. The length of the pipe is 5 m and the thread diameter is 25 mm. Since the pipe thickness is 1 mm, calculate the total heat transfer coefficient and the rate of heat transfer from the condensed steam to the water at 15 °C
a one shell and two tube pass heat exchanger, coolant enters the tube at 4.81 kg/s (spread over 72 tubes with each tube being 0.01 m in diameter and 1.95 m length) at an initial temperature of 25 C. Water enters the shell at 2.5 kg/s at an initial temperature of 5 C. The average convection coefficient of the water is known to be 1e4 W/m2.K. What is the overall heat transfer coefficient, assuming no fouling, negligible tube thermal resistance and near-identical inner and outer tube surfaces? What is the actual heat transfer rate? What is the coolant outlet temperature? The coolant properties are Cp = 1040 J/kg.K, μ = 7.65e-4 kg/s.m, k = 0.058 W/m.K and Pr = 14. Assume the water Cp = 4200 J/kg.K.
A counter-flow heat exchanger is used to cool water from 60°C to 20°C. The water flows at 0.2 m/s through the inner tube and the cooling fluid flows in the enclosure. The inner tube is 6-cm in diameter and 15-m in length. It is thin and made of copper. The flow rate of the cooling fluid is 1.2 kg/s and convection coefficient is 360 W/m².°C. The specific heat of the cooling fluid is 1600 J/kg. °C. The surface temperature of the inner tube can be approximated as almost isothermal. (a) What is the mass flow rate of water? 0.56 kg/s (b) What is the effectiveness of this heat exchanger? 0.285
Water (cp = 4180 J/kg·K) enters the 2.5-cminternal- diameter tube of a double-pipe counter-flow heat exchanger at 17°C at a rate of 1.8 kg/s. Water is heated by steam condensing at 120°C (hfg = 2203 kJ/kg) in the shell. If the overall heat transfer coefficient of the heat exchanger is 700 W/m2·K, determine the length of the tube required in order to heat the water to 80°C using (a) the LMTD method and (b) the «-NTU method.
A condenser consists of 5 pieces of 3 m long 1/4 in Sch 40 horizontal pipes lined up in 6 rows. It transfers cooling water with a heat transfer coefficient of 2000 W / m-K through the pipes. As the flow rate of the water is very high, the water temperature is constant at 35 degrees Celsius. Saturated heat vapor condenses at a pressure of 2 bars outside the pipes. Calculate the condenser capacity in kW
A circular tube (internal diameter=8 mm, length=20 m) subjected to a uniform heat flux of 30000 W/m2 on its surface. Water (ρ=1000 kg/m3, k=0.6 W/mK, ν=8x10-7 m2/s, cp=4.2 kJ/kg0C, Pr=6) enters the tube at 15 oC with a velocity of 1.1 m/s and leaves at 50 0C. Surface temperature of the tube at the inlet is
Consider the flow of motor oil (cp=2048 J/kg K) through a copper tube ofthin wall at a rate of 0.3 kg/s. The oil enters the copper tubes at atemperature of 80°C that is cooled by means of water that enters at 20°C. Temperatureoutlet of the oil cannot be higher than 40°C. The convective coefficient ofheat transfer from the oil side is 750W/m2 K and from the water side 350W/m2 K. IfThe outlet temperature of the water is measured at 32°C and a heat exchanger is considered.double tube in parallel. Determine: a) Mass flow rate of the water. b) The difference of log mean temperatures. c) the area of the heat exchanger.
A long counter-flow heat exchanger cools water from 40°C to 10°C by passing the water via the inner tube through an enclosure of cold fluid. The water is flowing through a 3-cm diameter tube at a rate of 0.27 kg/s. The cold fluid enters the enclosure at −10°C and has a convection coefficient of 1200 W/m².K. The mass flow rate of the cold fluid and its specific heat are 1.2 kg/s and 1340 J/kg-K, respectively. (a) Assuming the flow is fully developed, find out the convection coefficient of the water flow. (b) What is the length of the heat exchanger? 1554 W/m²K 2 21.9m Water Cold Fluid
Please help me fast
Please answer
Please solve this question, thank you very much
A two-shell passes and four-tube passes heat exchanger is used to heat glycerin from 20°C to 50°C by hot water, which enters the thin-walled 2-cmdiameter tubes at 80°C and leaves at 40°C. The total length of the tubes in the heat exchanger is 60 m. The convection heat transfer coefficient is 25 W/m2∙K on the glycerin (shell) side and 160 W/m2∙K on the water (tube) side. Determine the rate of heat transfer in the heat exchanger (a) before any fouling and (b) after fouling with a fouling factor of 0.0006 m2∙K/W occurs on the outer surfaces of the tubes.