A long counter-flow heat exchanger cools water from 40°C to 10°C by passing the water via the inner cube through an enclosure of cold fluid. The water is flowing through a 3-cm diameter tube at a rate of 0.27 kg/s. The cold fluid enters the enclosure at -10°C and has a convection coefficient of 1200 W/m².K. The mass flow rate of the cold fluid and its specific heat are 1.2 kg/s and 1340 J/kg-K, respectively. (a) Assuming the flow is fully developed, find out the convection coefficient of the water flow. (b) What is the length of the heat exchanger? 1554 W/m²K 21.9m Water Cold Fluid

A long counter-flow heat exchanger cools water from 40°C to 10°C by passing the water via the inner cube through an enclosure of cold fluid. The water is flowing through a 3-cm diameter tube at a rate of 0.27 kg/s. The cold fluid enters the enclosure at -10°C and has a convection coefficient of 1200 W/m².K. The mass flow rate of the cold fluid and its specific heat are 1.2 kg/s and 1340 J/kg-K, respectively. (a) Assuming the flow is fully developed, find out the convection coefficient of the water flow. (b) What is the length of the heat exchanger? 1554 W/m²K 21.9m Water Cold Fluid

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q3 / Draw the following spring with all dimensions in sheet (write down all the equations you used in the :drawing if found) D1 70 mm D2 50 mm L 125 mm d 10 mm Pitch 25 mm
Please do #4
- For the slider – crank mechanism illustrated in Fig.2 A) Determine all instant centers.
Which tools that can be used to :2 draw the following shape in .AutoCAD O Polygon, Hatch line, Polyline, Circle, and Construction lines Hatch lines, Circle, Line, Rectangle, and Polyline Construction lines, Hatch line, Polyline, Circle, and Line Trim, Line, Circle, Layer, Polyline and Arc O
1. If a machinist wanted to drill a % inch hole in a piece of machine steel using a high speed steel drill. At what speed in revolutions per minute should he operate the drill press? 2. Find the revolutions per minute of an 8 mm drill if it is used to cut an aluminum workpiece using a high carbon steel drill. 3. The rpm setting of the drill press is set to 600 rpm. What is the maximum diameter in inches of a high speed drill if it is used to drill a tool steel material? 4. A drill press has the following rpm settings; 350, 600, 1100, & 1600. What rpm setting must be used if a 15 mm high speed steel drill is used to cut brass workpiece? 5. A machine operator drills a hole of a 3/8 inch diameter to a stainless steel using a carbon steel drill. He sets the drill press rpm setting to 900 rpm. Is he operating at correct setting? If not, then what must be the correct rpm setting considering that the machine has the following rpm settings of 300, 600, 900, 1200, and 1800?
Question 1 Figure Qta shows two cables attached to a half-ring anchor point as shown in Figure Q1a. Force Fi acts vertically with a force of 2170 N; and F2 acts at an angle e relative to the y-axis with a force of 1240 N. F1 F2 Figure Qta Cable Anchor Point a) For Figure Q1a, at what angle @ must the force F2 ( 1240 N) be applied in order that the resultant force R of the two forces Fi and F2 has a magnitude of 3100 N? Give your answer in degrees to 2 decimal places. b) For Figure Q1a, what is the angle between the resultant force R (3100 N) and the yaxis. Give your answer in degrees to 2 decimal places. c) The pulley system shown in Figure Q1c lifts a mass, m, of 550 kg. Calculate the force Fanecessary to maintain the suspended mass in static equilibrium; and determine the forces at the ceilling anchor points A and B. Assume frictionless and weightless pulleys and useg-9.81 m/s'.
Draw the kinematic diagram of the shape gear 6 Slot Cam 6 - rod 3 Slider 7 child 5 rod 4 rod 2 Pressure bar 8 01 Eccentric 1 Gear 1 Frame 9
Before After False True O
Q5
Gears box has (10)Ten speeds, If the minimum and maximum velocity equal to (100)m/min. and (500)m/min respectively, computed the Arithmetic Progression and Geometric Progression?
Solve correctly please.
If gear 1 turns 620 degrees, how many degrees will gear 3 turn? N1 =20, N2=10, N3=50