Liquid ammonia at -20°C (rho= 665.1 kg/m³ and μ = 2.361*10-4 kg/m*s) is flowing through a 20 m long section of a 5 mm diameter copper tube with friction factor 0.01819 at a velocity of 9.19 m/s and differential pressure of 2043.05 kPa then the pumping power required to push the liquid is Liquid O W L D

Liquid ammonia at -20°C (rho= 665.1 kg/m³ and μ = 2.36110-4 kg/ms) is flowing through a 20 m long section of a 5 mm diameter copper tube with friction factor 0.01819 at a velocity of 9.19 m/s and differential pressure of 2043.05 kPa then the pumping power required to push the liquid is Liquid O W L D

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.28P

See similar textbooks

Similar questions

Liquid L D Liquid ammonia at -20°C (rho=665.1 kg/m³ and μ = 2.361*10-4 kg/m*s) is flowing through a 35 m long section of a 5 mm diameter copper tube at a rate of 0.1 kg/s then the Reynold's number is
V(m/s) V(m/s) Q=2000 IIIIII air D-0.1m Air at (3.15x102) K is entering in a circular pipe at 101325 Pa as shown in Figure. The velocity of the air at the pipe entrance is (2.000x100) m/s. The diameter of the pipe is 0.1m. Specific gas constant of air is 287 3/kg-K. Specific heat of air is 1000 1/kg-K Find the outlet temperature i 2000 J of heat is added to the pipe.
Liquid ethylene is flowing through a nom 4 – 80S std type commecial steel pipe at -40°C. The tube is 300 m long. The outlet to the tube is 50 m higher than the inlet. As the ethylene passes through this pipe, it experiences a pressure drop of 500 kPa. Determine the volumetric flow rate of ethylene through the tube
An coconut oil (considered as viscous fluid) must be pumped between two buildings in an agro-industrial plant through an AISI 304 stainless steel pipe spread on the ground that has an outside diameter of 22 cm and 110 m long. To facilitate pumping, the liquid will be heated to 40 ° C in order to reduce its viscosity. The oil flow rate will be 20 Kg / s and the specific heat will be 1300 J / Kg K. Determine the temperature drop that the liquid will experience along the pipeline under the following operating conditions:Ambient air temperature = 10 ° CWind speed = 14 m / sPipe surface temperature = 37 ° C
A liquid metal flows at the rate of 4kg/s through a constant heat flux 6cm inner diameter tube in a nuclear reactor. The fluid at 200 oC is to be heated with the tube wall 40 oC above the fluid temperature. Determine the length of the tube required 25 oC rise in bulk fluid temperature. Using the following properties: ρ = 7700 kg/m3 , Y = 8*10-8 m2/s , Pr=0.011 , Cp= 130 J/kg.K , k=12W/mk. please can you solve it with keyboard,take your time heat transfer, J.P.Holman .
I need the answer as soon as possible
I need the answer as soon as possible
Tout=? V (m/s) D=0.1m air Air at (3.10x10^2) K is entering in a circular pipe at 101325 Pa as shown in Figure. The velocity of the air at the pipe entrance is (1.0000x10^O) m/s. The diameter of the pipe is 0.1m. Specific gas constant of air is 287 J/kg-K. Specific heat of air is 1000 J/kg-K. Find the outlet temperature if 2000 J of heat is added to the pipe. Answer should be in 'K' with three significant figures. Note: Your answer is assumed to be reduced to the highest power possible.
Harry up plz
Liquid water enters a 10-m-long smooth rectangular tube with a 50 mm and b = 25 mm. The surface temperature is kept constant, and water enters the tube at 20°C with a mass flow rate of 0.25 kg/s. Determine the tube surface temperature necessary to heat the water to the desired outlet temperature of 80°C Find the pumping power. Te
Example 3 Glycerin at 40 0C with p = 1252 kg/m³ and µ 0.27 kg/m.s is flowing through a 5 cm diameter horizontal smooth pipe with a mean velocity of 3.5 m/s. Determine the pressure drop per 10 m of the pipe.
ANSWER IN DETAILED SOLUTION