Part-2 -3 Water at 12°C (p = 997 kg/m and p = 1.138 x 10 kg/m-s) is flowing steadily in a 25- m-long and 5-cm-diameter horizontal pipe made of stainless steel at a rate of 9 L/s. Given that the pipe has a sharp-edged inlet and five 90° smooth flanged bends. Determine (c) the pumping power requirement to overcome this pressure drop.

Part-2 -3 Water at 12°C (p = 997 kg/m and p = 1.138 x 10 kg/m-s) is flowing steadily in a 25- m-long and 5-cm-diameter horizontal pipe made of stainless steel at a rate of 9 L/s. Given that the pipe has a sharp-edged inlet and five 90° smooth flanged bends. Determine (c) the pumping power requirement to overcome this pressure drop.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

As a test to determine the effective wall roughness of an existing pipe installation, water at 10°C is pumped through it at the rate of 300 L/min. The pipe is standard steel tubing, 40 mm OD x 3.0 mm wall. Pressure gages located at 25 m apart in a horizontal nm of the pipe read 1235 kPa and 849 kPa. Determine the effective pipe wall roughness.
A boy has a tank with a rectangular bottom base 40 cm by 50 cm and a height of 100 cm. The tank is initially empty and is equipped with an orifice 3 mm square (Cv=0.96 and Cc=0.62) located at the bottom of the tank. The boy first closed the orifice and start pouring water into the tank at a constant rate of 0.05 li/s. After 30 minutes, without the boy noticing it, the orifice was accidentally opened and it took another 30 minutes when the boy noticed that the orifice was already opened. What is the depth of water in the tank at that moment?
Water at 15°C (p = 999.1 kg/m³ and u kg/m · s) is flowing steadily in a 30-m-long and 4-cm-diameter horizontal pipe made of stainless steel at a rate of 8 L/s. Deter- mine (a) the pressure drop, (b) the head loss, and (c) the pump- ing power requirement to overcome this pressure drop. 1.138 × 10–3 8 L/s 4 cm 30 m O
A metal pipe (ID: 20 cm, friction factor: 0.012) is used to deliver cooling water (10°C) from Tank A (elevation: 250 m) to Tank B (elevation: 275 m). Both tanks are cylindrical and have the same bottom diameter of 20 m). The head space pressures of Tank A and Tank B are 15.1 psia and 14.8 psia, respectively. The total pipe length is 2000 m, with two wide- open angle valves in between. The minor loss coefficients involved are 0.5 (pipe entrance), 5.0 (angle valves), and 1.0 (pipe exit). To deliver water at 200 GPM, how much energy (in kWh) will the pump most approximately consume in 12 hours if the pump efficiency is 85%? 32.6 kWh 45.1 kWh 57.9 kWh 38.4 kWh
The oil whose temperature is constant at 20 ° C (ρ = 886 kg / m3, μ = 0.805 kg / m / s) flows continuously and fully developed from a length of 40 m of a pipe with a diameter of 5 cm. The pressure at the inlet of this 40 m length was measured as 720 kPa and the pressure at the outlet as 101 kPa. Flow is laminar. Volumetric flow rates, average velocities, Reynolds numbers and Darcy friction factorsa) The pipe is horizontalb) The pipe makes 20 ° counterclockwise with the horizontal.c) The pipe makes 15 ° clockwise with the horizontal.Calculate for situations.
The air velocity in the duct of a heating system is to be measured by a Pitot-static probe inserted into the duct parallel to the flow. If the differential height between the water columns connected to the two outlets of the probe is 3.2 cm, determine (a) the flow velocity and (b) the pressure rise at the tip of the probe. The air temperature and pressure in the duct are 45° C and 98 kPa, respectively
A horizontal pipe has an abrupt expansion from D1 = 5 cm to D2 = 10 cm. The water velocity in the smaller section is 8 m/s and the flow is turbulent. The pressure in the smaller section is P1 = 410 kPa. Taking the kinetic energy correction factor to be 1.06 at both the inlet and the outlet, determine the downstream pressure P2, and estimate the error that would have occurred if Bernoulli’s equation had been used.
The owners of a smallholding water their vegetable garden using collected rainwater from atank. Thetankhasadiameterofbm,itisam tall and sits on a 6 m tall stand. The inner diameter of the hose is c cm, and the hose is (20 +5d) m long. If the tank was initially filled to the brim, how long will it take before the tank is empty? Assume that there is a single ball valve (K = 0.05) in the line, and that the spray nozzle has a hole diameter that is 20 % of the diameter of the hose. You may ignore all other losses in the nozzle. a = 9 b = 8 c = 7 d = 1 Hint: Use an Excel spreadsheet or C program for the calculations.
A 6cm diameter horizontal water pipe expands to a 10cm diameter pipe. The average velocity and pressure of water before the expansion section are 7 m/s and 150 kPa, respectively. Determine the head loss in the expansion section.
Water (Pw -3 1000 kg μω " m³ 1.8 x 107 Pas) flows through the shower system shown below. The pipe has a diameter of 4 cm, and contains three 90-degree bends (K₁ = 0.9), a partially open gate valve (K₁ =3.1), and a shower head (KL = 5.0). = Water flows out of the shower head at approximately the same velocity as it enters the pipe, 1.2 m/s. = The roughness of the pipe is 0.15 mm. Find the pressure (relative to atmosphere) of the water immediately before the first bend. Provide your answer in kPa. Neglect the horizontal parts of the pipe when calculating the length. h₁ =1.1 m, h₂=1.8 m, and h3 =0.4 m. h3 h₂ h₁
In a hydroelectric power plant, water at 20°C is supplied to the turbine at a rate of 0.55 m3/s through a 200-m-long, 0.35-m-diameter cast iron pipe. The elevation difference between the free surface of the reservoir and the turbine discharge is 140 m, and the combined turbine–generator efficiency is 85 percent. Disregarding the minor losses because of the large length-to-diameter ratio, determine the electric power output of this plant.
Water at 10 C flows in a 1.25-cm-diameter pipe at a rate of 1.33 L/min. The hydrodynamic entry length (in meters) is