Steam exiting the turbine of a steam power plant at 40°C is to be condensed in a large condenser by cooling water flowing through copper pipes (k = 386 W/m.°C) of inner diam- eter 1 cm and outer diameter 1.5 cm at an average temperature of 20°C. The heat of vaporization of water at 40°C is 2407 kJ/kg. The heat transfer coefficients are 13,000 W/m2.°C on the steam side and 200 W/m2.°C on the water side. Determine the length of the tube required to condense steam at a rate of 115 kg/h. Answer: 622 m Steam, 40°C 115 kg/h Cooling water Liquid water

Steam exiting the turbine of a steam power plant at 40°C is to be condensed in a large condenser by cooling water flowing through copper pipes (k = 386 W/m.°C) of inner diam- eter 1 cm and outer diameter 1.5 cm at an average temperature of 20°C. The heat of vaporization of water at 40°C is 2407 kJ/kg. The heat transfer coefficients are 13,000 W/m2.°C on the steam side and 200 W/m2.°C on the water side. Determine the length of the tube required to condense steam at a rate of 115 kg/h. Answer: 622 m Steam, 40°C 115 kg/h Cooling water Liquid water

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Heat transfer is of critical importance in various industrial applications, including manufacturing. During machining, both the cutting tool and the workpiece will be significantly heated by friction heating. The heating of the cutting tool will reduce the tool hardness and strength, deteriorate the cutting quality, and shorten the tool life. Therefore, it is essential to prevent the overheating of the cutting tool during machining. Coolants are an instrumental part of machining to help cool the tool and the workpiece, provide lubricant, flush away chips, and prevent corrosion. The task of this project is to design the coolant to maintain the maximum machine tool temperature below 100 °C during the side milling process. As shown in the figure below, the machine tool has a diameter of 10 mm (D) and a length of 5 cm. The tool material is M2 high speed tool steel (T11302) and the workpiece is aluminum 6061. The spindle speed (w) is 2000 RPM and the cutting speed (v) is 50 mm/min. The feed…
300960 W (e) Water is entering a heated tube at mass flow rate of 1.2 kg/s. The temperature at the inlet is 20°C and at the outlet is 80°C. Assume the surface temperature of the tube is 100°C. The convection coefficient of the water flow is 28 W/m².°c. The specific heat and density of water can be assumed to be 4180 J/kg.°C and 990 kg/m³. What is the rate of heat transfer to water during this process?
List and describe three methods of heat transfer. Give an example of each. (1) Method? Example? (2) Method? Example? (3) Method? Example?
Most automobiles have a coolant reservoir to catch radiator fluid that may overflow when the engine is hot. Such a radiator, made of copper, is filled to its 12-L capacity when at 10.0°C. -What volume of radiator fluid, in liters, will overflow when the radiator and fluid reach their 99.5°C operating temperature, given that the fluid’s thermal coefficient of volume expansion is 400.0 × 10-6 / °C? The coefficient of volume expansion for copper is 5.1 × 10-5 /°C.
The interior walls as well the ceiling and the floor of a room are all at Tg = 10 deg C. The room air is continuously circulated, providing an average convection coefficient of 2.6 W m-2 K-1 at an average temperature of T₁ = 28 deg C. If the room measures 5 m X 4 m X 3 m, estimate the rate at which the air is cooling the room (a negative answer will imply the air is heating the room). Enter your answer using two significant digits in kW.
Question #7 Steam at 320°C flows in a stainless steel pipe (k-15W/m K) whose inner and outer diameter are 5cm and 5.5cm respectively. The pipe is covered with 3cm thick glass wool insulation (-0.038W/mK). Heat is lost to the surroundings at 5°C by natural convection and radiation, with a combined natural convection and radiation heat transfer coefficient of h 15W/m² K. Taking the heat transfer coefficient inside the pipe to be happe = outside pipe = 80 W/m²K. (A) Draw the schematic diagram of this problem and label all quantities. (B) Draw the thermal network diagram of this problem and label all thermal resistors and the direction of heat flow. (C) Determine the (i) inner surface area (ii) outer surface area (iii) inner thermal resis- tance (iv) outer thermal resistance (v) thermal resistance across pipe and (vi) thermal resistance across insulation. (D) Determine the total thermal resistance for the unit length of pipe. (E) Determine the rate of heat loss from the steam per unit…
Only need assumptions and fbd
Will definitely upvote
Steam condenses at 100°C on the outer surface of a pipe with a thermal conductivity of 180 J/ms°C. The surface heat transfer coefficient of the water flowing in the pipe is 4000 J/m²s°C, and the heat transfer coefficient created by the steam condensing outside is 10000 J/m²s°C. The length of the pipe is 5 m and the thread diameter is 25 mm. Since the pipe thickness is 1 mm, calculate the total heat transfer coefficient and the rate of heat transfer from the condensed steam to the water at 15 °C
A steam condenser operates at 61 cm of Hg vacuum. The steam enters the condenser with a moisture content of 87%. Cooling water is supplied to the condenser at a temperature of 20 C with a terminal difference of 5 C. The water velocity of water inside the tube is to be limited to 2.5 m/s when using 2.5 cm outside diameter tubes whose thickness is 1.75 mm. The overall heat transfer coefficient of the tubes could be approximated by the equation U = 1213.4(v1/2), W/(m2-C) where v is the water velocity in m/sec. Determine: 1. The required mass flow of cooling water, kg/s 2. The required capacity of the circulating pump, liter per second 3. The Logarithmic Mean Temperature Difference, C 4. The required Number of tubes 5. The required length of tubes, (m), and number of passes
Mechanical services
e