Steam enters the first-stage turbine shown in Figure (right) at 40 bar and 500°C with a volumetric flow rate of 90 m³/min. Steam exits the turbine at 20 bar and 400°C. The steam is then reheated at constant pressure to 500°C before entering the second-stage turbine. Steam leaves the second stage as saturated vapor at 0.6 bar. For operation at steady state, and ignoring stray heat transfer and kinetic and potential energy effects, determine the a. mass flow rate of the steam, in kg/h. b. total power produced by the two stages of the turbine, in kW. Steam P₁= 40 bar 7₁-500°C (AV), -90 m/min Turbine P20 bar 7₂-400°C Reheater h Quer Turbine Py=20 bar 7₁-500°C Saturated vapor. Pa 0.6 bar Power

Steam enters the first-stage turbine shown in Figure (right) at 40 bar and 500°C with a volumetric flow rate of 90 m³/min. Steam exits the turbine at 20 bar and 400°C. The steam is then reheated at constant pressure to 500°C before entering the second-stage turbine. Steam leaves the second stage as saturated vapor at 0.6 bar. For operation at steady state, and ignoring stray heat transfer and kinetic and potential energy effects, determine the a. mass flow rate of the steam, in kg/h. b. total power produced by the two stages of the turbine, in kW. Steam P₁= 40 bar 7₁-500°C (AV), -90 m/min Turbine P20 bar 7₂-400°C Reheater h Quer Turbine Py=20 bar 7₁-500°C Saturated vapor. Pa 0.6 bar Power

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Hi, can you only help with part a of the following?
Refrigerant 134a enters a horizontal pipe operating at steady state at 40°C, 300 kPa, and a velocity of 25 m/s. At the exit, the temperature is 50°C and the pressure is 240 kPa. The pipe diameter is 0.055 m. Determine: (a) the mass flow rate of the refrigerant, in kg/s, (b) the velocity at the exit, in m/s, and (c) the rate of heat transfer between the pipe and its surroundings, in kW.
b) A nearly flat bicycle tire becomes noticeably warmer after it has been pumped up. Approximate this process as a reversible adiabatic compression. Take the initial pressure and initial temperature of the air before it is put in the tire to be P = 1.00 bar and T; = 298 K. The final volume of the air in the tire is V = 1.00 L and the final pressure is Pf = 5.00 bar. Hints: • Cy.m = 5/2 R. Heat Capacity ratio, y = Cp.m Cy,m = 1.4 %3D Cy,m For a reversible adiabatic change, 4 = (4 )°, where c = R For perfect gas: CP.m - Cv,m = R CP.m and Cv.m denote molar heat capacity at constant pressure and volume, respectively. Tand V are temperature and volume at initiate (i) state ad final (f) state. i) Derive a mathematical expression to show the relationship of temperature, volume and heat capacity ratio (y) for the transformation of this process from initial to final states.
Water stored in a large, well-insulated storage tank at 21oC, and atmospheric pressure is being pumped at steady state from this tank by a pump at the rate of 40m3/h. The motor driving the pump supplies energy at the rate of 8.5 k.W. The water is used as a cooling medium and passes through a heat exchanger where 255 k.W of heat is added to the water. The heated water then flows to a second large, vented tank, which is 25 m above the first tank. Determine the final temperature of the water delivered to the second tank.
Carbon dioxide gas is compressed at a steady state from a pressure of 16 lbf/in2 and a temperature of 32oF to a pressure of 50 lbf/in2 and a temperature of 130oF. The gas enters the compressor with a velocity of 30 ft/s and exits with a velocity of 80 ft/s. The mass flow rate is 3500 lb/hr. The magnitude of the heat transfer rate from the compressor to its surroundings is 5% of the compressor power input. Use the ideal gas model with cp = 0.21 Btu/lb·oR and neglect potential energy effects. A.) Determine the flow area at the inlet, in ft2, B.) and the power required by the compressor to work, in horsepower. Show complete solutions.
Water vapor with a pressure of 160 bar and a temperature of 480°C enters a stable turbine with a volumetric flow of 800 m3/min. About 18% of the incoming mass flow exits a part of the turbine at a pressure of 5 bar, a temperature of 240°C and a velocity of 25 m/s. The rest comes out from another part of the turbine with a pressure of 0.06 bar, a quality of 94% and a speed of 400 m/s. Determine the diameters of each outlet channel in m.
13. During a reversible process, 2.09 kg/s of gas rejects 322.9 kJ/s of heat isothermally at 25.5°C. For this gas, cp = 2.14 kJ/kg K and c, 1.62 kJ/kg K. The initial pressure is 551.7 kPa. Determine the work steady flow of the process in hp if APE = 2.8 kJ/s and AKE = 6.2 kJ/s.
A rigid cylindrical tank stores 80 kg of a substance at 400 kPa and 480 K while the outside temperature is 290 K. A paddle wheel stirs the system transferring shaft work at a rate of 0.7 kW. At the same time an internal electrical resistance heater transfers electricity at the rate of 1.6 kW. A. Do an energy analysis to determine the rate of heat transfer for the tank. B. Determine the absolute value of the rate at which entropy leaves the internal system (at a uniform temperature of 480 K). Answer in kW/K C. Determine the rate of entropy increase in the system's surroundings. Answer in kW/K
Carbon dioxide gas is compressed at steady state from a pressure of 18 lb-/in² and a temperature of 32°F to a pressure of 50 lb-/in² and a temperature of 110°F. The gas enters the compressor with a velocity of 30 ft/s and exits with a velocity of 80 ft/s. The mass flow rate is 4000 lb/hr. The magnitude of the heat transfer rate from the compressor to its surroundings is 5% of the compressor power input. Use the ideal gas model with cp = 0.21 Btu/lb.ºR and neglect potential energy effects. Determine the flow area at the inlet, in ft², and the power required by the compressor to work, in horsepower. Step 1 Determine the flow area at the inlet, in ft². A₁ = i ft²
Steam at 350 °C , 10 bar is expanded through an adiabatic nozzle to 250 °C and 5 bar. Neglect the inlet kinetic energy of the steam. 1.Determine the velocity of exiting steam, 50 m below the inlet. 2.Calculate the degrees of superheat of the exiting steam.