Hi, can you only help with part a of the following? 31 kg/s of water enters a turbine at 4 MPa and 500°C (state 1) and leaves the turbine at 10 kPa (state 2).After leaving the turbine, the hot water (that is used to generate power) is condensed isobarically in acondenser (heat exchanger) to 40°C (state 3). The energy from the hot water is absorbed by cold liquidwater that enters the condenser at 20°C (state 5).a) If the power output of the turbine is 30 MW, what is thestate of the water at the outlet of the turbine? If it is asaturated mixture, calculate its quality.b) What is the rate of heat transfer from the hot process water(that is used to generate power) to the cold cooling water?c) What is the mass flow rate of the cold cooling water? Youmay treat the cooling water as having a constant specificheat at an appropriate average temperature. There isnegligible pressure drop on the cooling water side of theheat exchanger. Show that you can make this calculation 2different ways:i.ii.by considering just the cooling water side of thecondenser as your control volume.by considering the entire condenser as your controlvolume.P₁ = 4 MPaT₁:= 500°CTurbineMT3 = 40°C3WoutP₂ = 10 kPaT5=T6= 20°C= 35°C

mass flow rate of the waterPower output of the turbineAt 4 MPa and 500oC temperature, from the steam…

31 kg/s of water enters a turbine at 4 MPa and 500°C (state 1) and leaves the turbine at 10 kPa (state 2). After leaving the turbine, the hot water (that is used to generate power) is condensed isobarically in a condenser (heat exchanger) to 40°C (state 3). The energy from the hot water is absorbed by cold liquid water that enters the condenser at 20°C (state 5). a) If the power output of the turbine is 30 MW, what is the state of the water at the outlet of the turbine? If it is a saturated mixture, calculate its quality. P₁ = 4 MPa T₁ = 500°C 1 Turbine Wout

31 kg/s of water enters a turbine at 4 MPa and 500°C (state 1) and leaves the turbine at 10 kPa (state 2). After leaving the turbine, the hot water (that is used to generate power) is condensed isobarically in a condenser (heat exchanger) to 40°C (state 3). The energy from the hot water is absorbed by cold liquid water that enters the condenser at 20°C (state 5). a) If the power output of the turbine is 30 MW, what is the state of the water at the outlet of the turbine? If it is a saturated mixture, calculate its quality. P₁ = 4 MPa T₁ = 500°C 1 Turbine Wout

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

I am attaching both questions for 4 and 5 with the question in the image. thank you. NOTE : So the last person answered this question WITHOUT refencing the answer for whether question 4 or 5 answeres were given, so i am asking for question 5(or the answer for the question that was NOT solved because it was not referenced.) These were the following answers given to me from the last person on bartleby who answered my question without referencing whether it was the answer for question 4 or 5. 1 pass 2 fail 3 fail 4 pass
Help me solve this ENGINEERING GRAPHICS question Use 0.25 cartesian paper or 0.25 Isometric paper please.
Statics of Rigid Bodies Note: If you have already answered the problems in this post, kindly ignore it. If not, then answer it. Thank you, Tutor! Content Covered: - Method of Joints Direction: Create two problems based on the topic "Method of Joints" and then solve them with a complete solution. In return, I will give you a good rating. Thank you so much! Note: Please bear in mind to create two problems based on the topic "Method of Joints." Be careful with the calculations in the problem. Kindly double check the solution and answer if there is a deficiency. And also, box the final answer. Thank you so much!
LESSON: AUTODESK FUSION 360 Identify the feature displayed in the picture, and choose from choices below. Extrude Sketch Revolve Hole Pattern Create Form Press Pull Fillet Shell Combine Split Body Move Offset Plane Measure Canvas Select Windows Selection Crossing Selection Freeform Selection Paint Selection
I was given this image for the purpose of studying for an upcoming exam. No additional info was given. Any suggestions on how to study for potential questions that could be asked about this image?
You are a biomedical engineer working for a small orthopaedic firm that fabricates rectangular shaped fracture fixation plates from titanium alloy (model = "Ti Fix-It") materials. A recent clinical report documents some problems with the plates implanted into fractured limbs. Specifically, some plates have become permanently bent while patients are in rehab and doing partial weight bearing activities. Your boss asks you to review the technical report that was generated by the previous test engineer (whose job you now have!) and used to verify the design. The brief report states the following... "Ti Fix-It plates were manufactured from Ti-6Al-4V (grade 5) and machined into solid 150 mm long beams with a 4 mm thick and 15 mm wide cross section. Each Ti Fix-It plate was loaded in equilibrium in a 4-point bending test (set-up configuration is provided in drawing below), with an applied load of 1000N. The maximum stress in this set-up was less than the yield stress for the Ti-6Al-4V…
A.) Sketch:[Draw a sketch that represents the situation of the problem, while showing all the variables included in it (vectors or scalars as forces, , displacement, position, etc.).] B.) Approach:[Mention all the laws, principles or concepts, as well as the mathematical equations that solve this problem. Step by step.] C.)Solution:[Develop the physical or mathematical equations used for the solution of the problem and highlight the partial and final answers. Be clear and organized.]