Steam enters the condenser of a steam power plant at 20000 kPa and a quality of 95 percent with a mass flow rate of 20 Mg/h. It is to be cooled by water from a nearby river in circulating the water through the tubes within the condenser. To prevent thermal pollution, the river water is not allowed to experience a temperature rise above 10°C. If the steam is to leave the condenser as saturated liquid at 20000 Pa, determine the mass flow rate of the cooling water required. m, = 20,000 kg/h P, = 20 kPa = 0.95 Steam Water T,+ 10°C P = 20 kPa Sat. liquid

Steam enters the condenser of a steam power plant at 20000 kPa and a quality of 95 percent with a mass flow rate of 20 Mg/h. It is to be cooled by water from a nearby river in circulating the water through the tubes within the condenser. To prevent thermal pollution, the river water is not allowed to experience a temperature rise above 10°C. If the steam is to leave the condenser as saturated liquid at 20000 Pa, determine the mass flow rate of the cooling water required. m, = 20,000 kg/h P, = 20 kPa = 0.95 Steam Water T,+ 10°C P = 20 kPa Sat. liquid

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Air (MW=29 g/mol) at 115.00 kPa and 285.00 is compressed steadily to 600.0 kPa. The mass flow rate of the air is 2.00 kg/s and a heat loss of 32.1 kW occurs during the process. You may assume that changes in kinetic and potential energy are negligible, the temperature of the surroundings is 25 ∘C, and that the CP of air is 3.5 R. Given the compressor operates with a second law (reversible) efficiency of 0.60,calculate the following. What is the actual work interaction term in kW? What is the actual exit temperature of the air in Celcius?
Refrigerant 134 A enters in a condenser of a heat pump at 180 kPa and -4 0C and exits with a quality of 0.8 and the same pressure of 180 kPa. The mass flow rate of the refrigerant is 65 kg/h, and the heat pump compressor consumes 45 kJ/min of power. Determine the coefficient of performance of the heat pump. Type your answer in the first box.
1. Steam at a pressure of 2MPA and temperature 300°C is passed at a constant rate into a desuperheater unit. The desuperheater is accomplished by continuously spraying water at 95 °C onto incoming superheated steam. The amount of water injected is so regulated that both the water and superheated steam finally change into dry steam at 2 MPa. If the resulting mixture of dry saturated steam leaves the desuperheater at 2MPA and the rate of I kg/s, find the mass of superheated steam used per hour and the mass of water to be injected per hour. Fond also the diameter of the pipe through which the superheated steam flows to the superheater if the speed of the steam through the pipe is not to exceed 25m/s..
Refrigerant-134a (R-134a) enters the expansion valve of a refrigeration system at 650 kPa with a quality of 20%. The pressure of R-134a at the outlet is 200 kPa. a)Determine the temperature of R-134a at the outlet in oC. Calculate the difference of internal energy between the outlet and inlet in kJ/kg
The valve connected to a 450-liter insulated tank of air at 250 kPa and 50̊C is opened,allowing the gas to escape until its pressure drops to 120 kPa. An electric heater insidethe tank maintains the temperature at 50̊C. Using variable specific heats, Determine thefollowing:a) The mass of air withdrawn (kg)b) The energy input to the resistor (kJ)
An adiabatic capillary tube is used in some refrigeration systems to drop the pressure of the refrigerant from the condenser level to the evaporator level. The R-134a enters the capillary tube as a saturated liquid at 50°C and leaves at -22.00°C. Determine the quality of the refrigerant at the inlet of the evaporator. Use data from the tables. (Round the final answer to three decimal places.) The quality of the refrigerant is
A 0.25 m3 rigid tank contains refrigerant-134a at 0.8 MPa and 100 percent quality. The tank is connected by a valve to a supply line that carries refrigerant-134a at 1.5 MPa and 30 ∘C. The valve is opened and the refrigerant is allowed to enter the tank. The valve is closed when it is observed that the tank contains saturated liquid at 1.5 MPa. Part A Determine the heat transfer (Q). Part B Determine the mass of the refrigerant that has entered the tank.
An adiabatic steam turbine receives steam from two boilers. One flow has a mass flow rate (rim) of 5.7 kg/s at 3 MPa and 600 °C. The other flow has a mass flow rate (m) of 6.0 kg/s at 0.5 MPa and 600 °C. The exit flow is at 10 kPa with a quality of 100%. Neglect ΔΚΕ (Higure 1) Part A Determine the total power output. Express your answer to three significant figures. Vα ΑΣΦ vec ? MW Submit Request Answer Part B Provide Feedback Figure West
A steam power plant has a high pressure of 2.5 MPa after release from the pump and it maintains 40°C in the condenser. The quality of the stream exiting the turbine is 80%. Solve for the work produced by the turbine and the pump, the heat transfer in the boiler, and heat removed by the condenser. (Answer in kJ/kg)
Determine the rate of heat released (in kW) by the steam with 88.0% quality that enters the evaporator at 1800 kg/h at 132C and exits as a subcooled liquid at 100C. Assume that the condensate outlet pressure is the same as the steam inlet pressure. The specific heat of liquid water is 4.187 kJ/kgC.
Refrigerant-134a is compressed steadily from the saturated vapor state at 120 kPa to 1.6 MPa and 60 °C at a rate of 0.27 kg/s. The compressor is losing heat at a rate of 1.6 kJ/s during compression. Determine the power input to the compressor. O10.0 kW 11.8 kW O 13.4 kW O 21.0 kW