Statement Consider the following statements and choose the correct option: 1: Silicon is not suitable for switching appliances. Statement 2: Germanium is suitable for high frequency appliances. Select one option A B C D Statement 1 is true, but Statement 2 is false. Statement 1 is false, but Statement 2 is true. Both statements are true. Both statements are false.

Statement Consider the following statements and choose the correct option: 1: Silicon is not suitable for switching appliances. Statement 2: Germanium is suitable for high frequency appliances. Select one option A B C D Statement 1 is true, but Statement 2 is false. Statement 1 is false, but Statement 2 is true. Both statements are true. Both statements are false.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

If a Si diode at room temperature (25°) has a leakage current IS = 56 nA, k = 5,800, and VD = 0.58 V, The diode current is ___mA. No need for a solution. Just write your numeric answer in the space provided. Round off your answer to 2 decimal places.
Sketch the electronic symbol (schematic) for the following components/ devices. Briefly describe the function of the electronic component and use the IEEE/ANSI standard symbol as indicated below. Fixed Resistor Any Variable Resistor Polarized Capacitor
4. General Purpose Diodes are mostly preferred in chopper circuits. Is it True? Justify. ( short answer only )
Suppose you are an electronic circuit designer. How you can use the center-taped step down transformer in bridge rectifier circuit?
2. Based on the given figure 2, explain the working principle of the Repeaters. Long cable Repeater Figure 2
Indicate which of the following statements refer to LCD displays and which refer to LED displays: a. Emit light b. Reflect ambient light c. Are best for low-power applications d. Require an AC voltage e. Use a 7-segment arrangement to produce digits f. Require current-limiting resistors
Question 1 AC supply voltage with f=50-Hz is connected to a bridge rectifier via a step-down transformer if the rectifier output is connected to a resistive load with 472 and the output power seen across the resistor is 2.5-watt a) Calculate the output peak voltage and current b) Calculate the secondary and primary ms voltages seen across the transformer c) Calculate the secondary and primary peak-currents seen across the transformer ) Draw the output instantaneous voltage and current showing the relevant peak and DC quantities c) Derive the instantaneous equations for the output ac voltage and current (seen across the resistor) Hint: use the 2" approximation (practical model) N-100 turns N-20 turns D3 DI f= 50 Hz D2 D4 R=470 R-2.5w
A diode is an example of ___ switch. A. SPDT B. passive C. active D. DPDT
A switch that can conduct positive on-state current, and can block positive or negative off-state voltage is called ___. A. voltage-bidirectional two-quadrant switch B. synchronous rectifier C. single quadrant switch D. four-quadrant switch
Which of the following statements about bridge tip rectifiers is false? A) If the 1-phase type has source inductance, the average value of the output voltage is lower than in the absence of the inductance. B) The average output voltage value of the 1-phase type is 0.9 times the peak voltage of the network. C) none D) There are only odd harmonics in the current drawn by the 1-phase type from the mains. E) The average value of the output voltage of the 3-phase type is larger as the 3-phase and 1-phase types are compared
Paragraph Styles Editing 1. In Solar PV modules, energy is converted to energy. 2. Choose the type of output voltage of a Solar PV module [AC/ DC]. 3.The PV cell is made of Material?
(01) AC Diode circuits. (Course: Electronic Devices and Circuit Theory) -Redraw the circuit, Assume diodes are off and Redraw, Apply KVL. -You can add //comments for a better understanding. -Please answer without abbreviation. -Make it clean and clear typing/writing. Thank you.