Question 2 (a) Analyze the complete voltage - current (V-I) characteristic of a diode. (b) Consider the filtered bridge rectifier circuit with a load in Figure 1. (i) Draw the voltage waveforms for Vin, Vrpri) Vpco) and V(oat)- (ii) Calculate the ripple factor. (iii) Re-calculate the ripple factor if the filter capacitor in Figure 1 is decreased to 1000 µF and the load resistance changes to 220 2. Write your observation regarding these changes. 10:1 D3 D 240 V rms Vripri Output 50 Hz RL 2200 μΕ D4 2.2 k2 All diodes are IN4001. Figure 1 elle

Question 2 (a) Analyze the complete voltage - current (V-I) characteristic of a diode. (b) Consider the filtered bridge rectifier circuit with a load in Figure 1. (i) Draw the voltage waveforms for Vin, Vrpri) Vpco) and V(oat)- (ii) Calculate the ripple factor. (iii) Re-calculate the ripple factor if the filter capacitor in Figure 1 is decreased to 1000 µF and the load resistance changes to 220 2. Write your observation regarding these changes. 10:1 D3 D 240 V rms Vripri Output 50 Hz RL 2200 μΕ D4 2.2 k2 All diodes are IN4001. Figure 1 elle

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Similar questions

How is a solid-state diode tested? Explain.
What is CEMF?
Q1 Figure Q1(a) is a full wave bridge circuit with a capacitor filter and the output waveform produced by the circuit is shown in Figure Q1(b). Assume all the diodes in the circuit have a forward voltage of 0.7 V. (a) (b) Sketch the waveform in A, B, C and D as shown in Figure Q1(a). Design the circuit by finding the value for the capacitor, C and the line voltage Vpri(rms) to the circuit to produce the output as shown in Figure Q1(b).
Draw the input waveform and output waveform for the circuit given below with proper values marked in the figure. Assume D1 as germanium and D2 as silicon diodes. Input Vpp%3D20V, V1=3 V and V2=10 V. R D2 D1 Vin Vout V1 V2 Maximum voltage of output waveform Minimum voltage of output waveform Ps
Q1 Figure Q1(a) is a full wave bridge circuit with a capacitor filter and the output waveform produced by the circuit is shown in Figure Q1(b). Assume all the diodes in the circuit have a forward voltage of 0.7 V. (a) Sketch the waveform in A, B, C and D as shown in Figure Q1(a). (b) Design the circuit by finding the value for the capacitor, C and the line voltage Vpri(rms) to the circuit to produce the output as shown in Figure Q1(b).
Draw the output waveform for the given circuit diagram with proper values and also mention the name of the circuit. The input waveform Vi is having a peak-to-peak value of 11 V and the bias voltage is 2 V. Assume diode to be silicon. Vo Maximum value of output waveform Minimum voltage of output waveform www
Determine the ripple factor for the filtered rectifier circuit below when RL= 4KO. Then explain briefly the effect of changing in the RL value on the output waveform. 5:1 Vp= 0.7v for all diodes Vma 100 V f= 60H2 D S0uF
What are the peak voltage values for both half cycles of the output waveform. V=35sin(wt). Use modified ideal diode model (Va=0.7V) for diodes. 5 k2 Z1 Vo Vi 20-V Zeners Z2 O34.30V, -34.30V O35.70V, -35.70V O 17.60V, -17.15V O35V, -35.00V OOv,oV Clear my choice
Please respond to question in attached image.
b) A single phase diode rectifier with RC load is connected to a grid with 240V and 50Hz. Find C value to have 20V ripple on the output side when output power is 100W.
In the circuit shown below. Determine the following a. Vs (at the secondary) b. Vout (across RL) c. Vrip (ripple votage) d. VDC e. PIV (Peak Inverse Voltage) 10:1 Output 115 V mis 60 Hz RL 2.2 k) D, 50μF- All diodes are IN4001. Tund AlMannai EENG261 Page 5/11
2.Sketch the waveforms for the load current and load voltage for the circuit show in Figure 2. Show the peak values. Use the offset diode model in your calculations. Input voltage source could be represented as a sine waveform, given as Vin=20sin(wt +30), and RL = 20 S Figure 2 www R₁ Vout