State an equation of vertical pressure in uniformly loaded rectangualr area ?

Q: Q.4) Determine the maximum mass m of cylinder for which the system shown below is in Static…

A: Given that, Mass of block = 50 Kg Static friction between block and plane = 0.15 Static friction…

Q: Two Steel Rods (ASTM A36) and One Aluminum Rod (1060 0) are assembled to two rigid cover plates. The…

A: Two Steel Rods (ASTM A36) and One Aluminum Rod (1060 0) are assembled to two rigid cover plates. The…

Q: Give an example of a flexure formula?

A: The flexure formula is also known as the flexure bending equation and is defined as; Where, M is…

Q: ynami

A: given: what is second law of thermo dynamic?

Q: Ratio of the temperature?

A: Given; Total emmisive power of a surface is; ∈1=500 W/m2At a given temperature=T1∈1=1200 W/m2At a…

Q: A 2-m long hollow steel shaft (G = 75 GPa) has an outside diameter of 75 mm and an inside diameter…

A:

Q: Project 1 A Vibration Insulation Problem Passive isolation systems are sometimes used to insulate…

A:

Q: Problems: For the following flows, find the equation of the streamline through (1,1). V = −y² i −…

A:

Q: Describe the stress involved in an unopened bottle of pop.

A: Solution:

Q: A 1500 kW electrical heater is used to heat 20 kg of water (cp=4186 J/kgK) lin an insulated bucket,…

A:

Q: Determine the average velocityof the particle during this time interval.

A:

Q: Is the Hotelling Rule applicable to oil?

A: Hotelling's hypothesis, often known as Hotelling's rule, states that nonrenewable resource…

Q: The instrument reads a height equivalent to 0.95 atm. The air is compressed adiabatically to 87,000…

A: GIVEN DATA- INTIAL PRESSURE = 0.95atm FINAL PRESSURE =87000Pa WE HAVE TO FIND PROPERTY AT FINAL…

Q: why the temperature increases during the compression proc

A: Given data Why the temperature increases during the compression process.

Q: What is quasistatic compression ?

A: "Quasi-static processes" are ideal reversible processes which cannot occur in practical(real…

Q: Why are the young modulus not used?

A: Tension in the wire is givenAnd working tensile strength is also gievn

Q: 6. From number 3, if the gas tank accident happened on top of Mt. Everest's summit where patm is…

A: Dear student,                     According to the guidelines I am allowed to answer only one…

Q: The conclusion of Inverse Square Law for Heat

A:

Q: What is the ideal column?

A: An ideal column is one that is perfectly straight, made of a homogeneous material, and free from…

Q: The tangential stress is produced twice that of the longitudinal stress in thin walled pressure…

A:

Q: What are the ultimate strengths in tension and in Compression for ASTM A48 Grade 40 cast iron?

A: Given data  What is the ultimate strength in tension and compression for ASTM A48 Grade 40

Q: DERIVE THE EQ GIVEN IN THE QUESTION.

A:

Q: 50 KN/m Determine the vertical deflection at the free end and the slope at the left support of the…

A:

Q: Write the nature of work done by an elongated spring?

A: The elongation produced in an ideal spring is directly proportional to the spring force F=−kx.

Q: Problem 3: Consider a critically damped oscillator. At time t = 0 it is sitting at its equilibrium…

A: Critical damping returns the system to equilibrium position as fast as possible without…

Q: Two identical metal blocks L and M (specific heat3D0.4 kJ/kg K). each having a mass of 5 kg, are…

A: Given:m=5 kgC=0.4 kJ/kg.KTL=TM=313 KTLf=293 K

Q: A calliper brake is required for the front wheels of a van with a braking capacity of 900 Nm for…

A: Given: The torque, T = 900 N.m The angle = 45 degrees The outer radius, R = 160 mm The inner radius,…

Q: Factor of safety??

A: Given; Principal stresses at a point in a critical section of a machine component are:σ1=60 MPaσ2=5…

Q: Explain the re guage

A: solution of above problem is below:

Q: Describe the Generalized Hooke’s Law?

A: The generalized Hooke's Law can be used to predict the deformations caused in a given material by an…

Q: save for Force in Rod AB: 1). Eguilibrium Equation (Sum of forces) (sum of forces) 2). Geometry…

A:

Q: ehavior of tensingrity bridge

A: Given Data : Tensegrity bridge

Q: What does the flexure formula describe?

A: A beam is failed due to the following criteria 1) Bending stress 2) Shear stress 3) Normal stress