4. If the chilled water is being supplied at 45°F, and the coil isselected so that the chilled water temperature rise is 10°F,what is the required chilled water flow through the coil inGPM?

Given :- Chilled water Temperature change (∆T) = 45°F - 10°F = 35°F To Find :- The required…

Answered: .If the chilled water is being supplied…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

15. A test tube for boiling water has a diameter of 25 mm. Water at a rate of 100 kg/h enters the uniformly heated tube. If pressure is 7.5 MPa, find the heat transfer coefficient and heat flux at a location where mixture quality is 0.25. ATsat = 10 C.
10. Use ASHRAE Table and Ph diagram 2019
For the purpose of acting as an air-cooled water chiller, an ammonia refrigerant vapor compression system is deployed. It is functioning with an evaporator temperature of 0 degrees Celsius and a condenser temperature of 40 degrees Celsius. The refrigeration produced by the system is equal to 15 tons.Find out: a. The temperature of the discharge and the mass flow rate of the refrigerant that is being circulated.b. The piston displacement that can be considered theoretical for the compressor.c. The work that can be done by the theoretical compressor.d. The heat that is not allowed to escape through the condenser.e. The Carnot coefficient of performance and the actual COP of the cycle.f. The volume of air that is supplied in the condenser if the air comes in at 30 degrees Celsius and exits at 34 degrees Celsius.g. The LMTD and AMTD of the condenser h. The water flow rate of the chiller assuming that the water enters the evaporator at 10 degrees Celsius and exits at 5 degrees Celsiusi. The…
_is the amount of heat transferred to water to produce the required quantity of steam Quality of steam O Capacity of boiler Quantity of steam Steaming rate
Example design a winter air conditioning power plant for a neighborhood of your choice (preheater/final heater andMust be humidification cells). Audible heat loss of the neighborhood is 50 kW, hidden heat gain is 20 kWhave been calculated. 1-) Show the process in the psychrometric diagram. 2-) Calculate the total amount of air circulating in the system 3-) Calculate the amount of water sprayed into the air in the humidifier 4-) Calculate the preheater capacity. 5-) Calculate final heater capacity
A refrigerant 22 refrigerating system is operating with a condenser temperature of 42°C and an evaporating temperature of 0°C. (a) If the liquid line from the condenser is soldered to the suction line from the evaporator to form a simple heat exchanger and if as a result of this the saturated vapor leaving the evaporator is superheated 10 degrees, how many degrees will the saturates liquid leaving the condenser be subcooled? Determine (b) the volume flow rate, and (c) the compressor work. Ans. (a) 5.3°C, (b) 1.102 L/s/TR, (c) 0.662 kW/TR
I need the answer as soon as possible
The figure-of-merit indicating the quality of a refrigeration unit is usually the coefficient of performance COP ≡ heat absorbed/net work put in What is the COP for this magnetic refrigeration device? (use wnet = 100 J/mol)
Figure below shows a steam jet refrigeration system that produces chilled water in a flash chamber. The chamber is maintained at a pressure by the steam ejector, which removes the vapor generated by entraining it in the low-pressure jet and discharging into the condenser. The vacuum pump removes air and other non-condensable gases from the condenser shell. For the conditions shown on the figure, determine the make-up water and cooling water flow rates in kg/hr. SHOW THE NEEDED DIAGRAMS FOR THE SOLUTION
1. A standard refrigerating system with a heat exchanger is operating with a condenser pressure of 1571.2 kPa and evaporator pressure of 421.35 kPa using refrigerant R22. If the liquid line from the condenser is soldered to the suction line from the evaporator to form a heat exchanger and if as a result of this, the saturated vapor leaving the evaporator is superheated by 10. Determine (a) temperature of refrigerant entering the compressor (b) temperature of refrigerant leaving the compressor (c) degree superheat leaving the compressor (d) temperature of subcooled liquid leaving heat exchanger (e) degree subcooled leaving the heat exchanger (f) mass of flash gas per kg refrigerant entering evaporator (g) compression ratio (h) clearance volumetric efficiency of compressor if the clearance volume is 5% 18 answers (i) refrigerating effect (i) mass flow rate of refrigerant per ton of refrigeration (k) work on compressor (1) work on compressor per ton of refrigeration (m) condenser load (n)…
what is the developed boiler horsepower if the steam rate is 0.85 kg/s and the factor of evaporation is 1.25? thank you!
1. A standard refrigerating system with a heat exchanger is operating with a condenser pressure of 1571.2 kPa and evaporator pressure of 421.35 kPa using refrigerant R22. If the liquid line from the condenser is soldered to the suction line from the evaporator to form a heat exchanger and if as a result of this, the saturated vapor leaving the evaporator is superheated by 10.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS

.If the chilled water is being supplied at 45°F, and the coil is selected so that the chilled water temperature rise is 10°F, what is the required chilled water flow through the coil in GPM?