Some graduate students have a solution of 1 M NaCl in the lab. What volume of the Nacl solution and what vorume of water do they need to mix together to make 1 L of 0.035 M NaC? O 35 ml of 1M NaCl and 35 mL of H20 O 35 mL of 1M NaCl and 965 mL of H20 O 35 mL of 1M NaCl and 65 mL of H20 O 3.5 mL of 1M Nacl and 6.5 mL of H20

Some graduate students have a solution of 1 M NaCl in the lab. What volume of the Nacl solution and what vorume of water do they need to mix together to make 1 L of 0.035 M NaC? O 35 ml of 1M NaCl and 35 mL of H20 O 35 mL of 1M NaCl and 965 mL of H20 O 35 mL of 1M NaCl and 65 mL of H20 O 3.5 mL of 1M Nacl and 6.5 mL of H20

Introductory Chemistry For Today

8th Edition

ISBN:9781285644561

Author:Seager

Publisher:Seager

Chapter7: Solutions And Colloids

Section: Chapter Questions

Problem 7.107E

See similar textbooks

Similar questions

An experiment in a general chemistry laboratory calls for a 2.00-M solution of HCl. How many mL of 11.9 M HCl would be required to make 250 mL of 2.00 M HCl?
An experiment calls for 100. mL of 1.25 M HC1. All that is available in the lab is a bottle of concentrated HC1, whose label indicates that it is 12.1 M. How much of the concentrated HC1 would be needed to prepare the desired solution?
Calcium carbonate, CaCO3, can be obtained in a very pure state. Standard solutions of calcium ion are usually prepared by dissolving calcium carbonate in acid. What mass of CaCO3 should be taken to prepare 500. mL of 0.0200 M calcium ion solution?
Which of the principal characteristics of solutions can we see in the solutions of K2Cr2O7 shown in Figure 11.2?
What volume of 0.250 M NaOH is required to react completely with 0.0100 moles of H2SO4? (a) 80.0 mL (b) 60.0 mL (c) 40.0 mL (d) 125 mL
Graph Table 14.10 shows solubility data that was collectedin an experiment. Plot a graph of the molarity ofKI versus temperature. What is the solubility of KI at55°C?
Addition of water to concentrated sulfuric acid is dangerous because it generates enough heat to boil the water, causing it to spatter out of the container. For this reason, chemists remember to add acid to water. In a dilution experiment, we calculate the amount of the more concentrated solution that must be measured out. If we place this concentrated solution (Figure 4.7) in the volumetric flask first, then dilute with water, we violate the caution Add acid to water. Describe a safer variation on the method shown in Figure 4.7 that allows the quantitative dilution of concentrated sulfuric acid. Figure 4.7 Preparing a dilute solution from a concentrated solution. (a) Draw the concentrated solution into a pipet to a level just above the calibration mark. (b) Allow the liquid to settle down to the calibration line. Touch the tip of the pipet to the side of the container to remove any extra liquid. (c) Transfer this solution to a volumetric flask. Again touch the pipet to the wall of the flask to ensure complete transfer, but do not blow out the pipet because it is calibrated for a small amount of liquid to remain in the tip. (d) Dilute to the mark with solvent. Frequently, especially with concentrated acids, it is best to have some solvent present in the volumetric flask before you add the concentrated sample.