Solve for the reactions, draw the shear and moment diagram, indicate the degree of the curve and box your maximum shear and moment.

Q: Determine the maximum torque that can be applied to a hollow circular steel shaft of 110-mm outer…

A: D=110mm d=80mm G=83GPa L=1000mm

Q: The system under the effect of torsion; a- Draw the torsional moment diagram. b- Determine the…

A: Determine a. Draw the torsional moment diagram. b. Angle of rotation at point C. c. Shear stress.

Q: A beam of T-section is pin-joint supported at point A and simply supported at point B with an…

A: Given Data:width b=65mmheight h=75mmthickness t =13mmP=4.5 kNq=2kN/mL1=1.25mL2=2.5mL3=1.5m

Q: Determine the weakest point on either the shear or moment diagram and draw the stress square at the…

A: A beam hinged supported at A and roller supported at B with two point loads 40 kN and 20 kN acting…

Q: The shaft is made from a solid steel section AB and a tubular portion made of steel and having a…

A:

Q: calculate the location of the centroid, the second moments and product of area for the cross-…

A: The objective of this question is to calculate the location of the centroid, the second moments and…

Q: a. Compute the internal forces in bars BC and CD. Indicate if they are in compression or tension.…

A: A truss member is given belowNeed to find a. compute the internal forces in bars BC and CD. Indicate…

Q: Determine the reactions at the supports, then draw the shear and moment diagram. Assume A is pin and…

A:

Q: *8-72. The hook is subjected to the force of 80 lb. Determine the state of stress at point A at…

A: Given :

Q: eter of the pin at C in mm.  c. Determine the corresponding bearing stress in the pedal at C in MPa.

A: Take moment about C∑ Mc=0TBA0.125-11000.3=0TBA=2640N∑ Fx=0TBA-Cx=0Cx=2640N∑ Fy=0 Cy=1100N…

Q: 4. Compute for the maximum value of force P that can be applied if the allowable bending stress is…

A:

Q: Q9. A circular steel tube of length L = 0.90 m is loaded in torsion by torques T. %3D (a) If the…

A: Solution; Given that: L=0.90 m r1=40mm

Q: A nylon thread is to be subjected to tension of Q (N). The modulus of elasticity, E of the thread is…

A:

Q: The moment acting on the cross section of the unequal-leg angle has a magnitude of 15 kN-m and is…

A: "Since you have posted the question with multiple sub-parts. We will solve the first two sub-parts…

Q: The stepped steel shaft carries the torque T. Determine the allowable magnitude of T if the working…

A: Given, ζ=12×106 PaDsmall=0.06 m

Q: The shäft iš made portion made of steel and having a brass core. If it is fixed to a rigid support…

A:

Q: Two 160 mm * t cover plates are welded to two cahnnels 200 mm high to form the cross section of the…

A: Introduction : Reactions : One of the most basic structures is the simply supported beam. Only two…

Q: A force P of magnitude 1,100 N is applied to the pedal shown satisfies a shearing stress in the pin…

A: Take moment about C∑ Mc=0TBA0.125-11000.3=0TBA=2640N∑ Fx=0TBA-Cx=0Cx=2640N∑ Fy=0 Cy=1100N…

Q: calculate the support reactions b. using the method of sections draw the shear force diagram AND…

A:

Q: The strain in the x direction at point A on the A-36 structural-steel beam(in figure attacched) is…

A: Neutral axis: YNA=122=6 inMoment of inertia:I=6×12312=864 in4   stress: stressσ=E×strain in x…

Q: If the beam is subjected to an internal moment of M = 30 kN-m determine the compressive bending…

A:

Q: The three member frame is subjected to the distributed load as shown in figure 1. Determine: a. Draw…

A: Given :

Q: The solid shaft is fixed to the support at C and subjected to the torsional loadings shown.…

A:

Q: The compound shaft is attached to a rigid wall at each end. For the bronze segment AB, the diameter…

A: Diameter of bronze = 68 mm Diameter of steel = 46 mm GB = 31.26 MPa GS = 84.92 MPa

Q: Rod BD is made of steel (E= 29 x 106 psi) and is used to brace the axially compressed member ABC.…

A: the rod BD is made of steel EBD=(29 x 106) psi= (29 x 103) ksi and it is used to brace the axially…

Q: The moment M acting on the cross section of the tee beam is oriented at an angle of 0 = 64° as…

A: A tee section is undergoing biaxial bending.The angle made by the moment axis with the vertical…

Q: A pin-connected structure is supported and loaded as shown. Member ABCD is rigid and is horizontal…

A:

Q: 2. Determine the internal normal force, shear force, and bending moment at point A in the rod. The…

A:

Q: A force P of magnitude 1,100 N is applied to the pedal shown satisfies a shearing stress in the pin…

A: Given data,  Applied force P = 1100 N  Shear Stress in the pin = 42 MPa  We have to determine the…

Q: Derive an expression of the maximum statical moment of area, Q and its location from the given…

A:

Q: Determine the location e of the shear center, point O, for the thin-walled member having the cross…

A: Given :

Q: The 60mm diameter steel shaft is subjected to the torques shown. Draw the FBD using double arrow…

A:

Q: The piece of plastic is originally rectangular. After the application of force, it deformed in the…

A: L = 500mm B = 800mm ∆Cx = a = 2mm∆Cy = b = 1.5mm∆Dx = c = 4mm∆Dy = b = 1.5mm

Q: Determine (a) the bending stress at point H. (b) the bending stress at point K. (c) the maximum…

A:

Q: Determine the maximum compressive bending stresses in the beam shown. Let P = 16 I= 100 x 106 mm P…

A:

Q: The shaft is made from a solid steel section AB and a bular portion made of steel and having a brass…

A:

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.