Solid circular shaft is under bending and torsion loadings. Uniaxial tensile yield strength of the material is 180 MPa, torque applied is 15 kN.m and bending moment applied is  3 kN.m. Calculate the value of the diameter d of the shaft based on the maximum-shear-stress theory of failure (Tresca criterion). Assume safety factor of 3

Q: The cold-drawn steel shaft has an ultimate strength of 1350 MPa, yield strength of 1200 MPa, and…

A:

Q: Two designs for a shaft are being considered. Both have an outside diameter of 70 m and are 900 mm…

A:

Q: Q3\ The cantilevered bar shown in the fig. made from steel Cold-drawn with (Sy = 280 MPa) and is…

A:

Q: A hollow aluminium tube used in a roof structure has an outside diameter 104mm and an inside…

A: A) Angle of twist for the given max shear stress in a hollow shaft: The angle of twist of a hollow…

Q: A simply supported shaft is shown. A constant magnitude distributed unit load p is applied as the…

A: Given: The safety factor, n = 2 The ultimate strength, Sut = 745 MPa The yield strength, Sy = 427…

Q: A shaft made of steel has the following minimum properties Se = 278 MPa, Sy = 412 MPa, and Sut = 551…

A:

Q: n outside diameter of 70 m and :

A: here outer dia (70m) is >>>> inner dia (50mm). so the polar moment of inertia almost…

Q: Solve the following problem Two designs for a shaft are being considered. Both have an outside…

A: Shear stress for solid shaft is given as  τ=16*Tπ*d3=16*325*1000π*703=4.825 MPa Shear stress for…

Q: the propeller on a ship shown in figure qi is subjected to a compressive axial force f of 180 kn as…

A:

Q: A 1.30-in.-diameter solid shaft is subjected to an axial force of P = 2000 lb, a horizontal shear…

A: Solution:

Q: A sleeve made of AISI 1040 CD steel has inner and outer diameters 40mm and 50mm, respectively. press…

A:

Q: A hollow tubular component is made of Steel having a Young's modulus of 205 GPa and yield strength…

A: E=205 GPaσy=250 MPad0=45 mmt=3 mmdi=45-2×3di=39 mmL= 4 ma if torque T=580 Nm then shear stress…

Q: Two designs for a shaft are being considered. Both have an outside diamete of 80 m and are 100 cm…

A:

Q: A bar of steel has the minimum properties Se= 40 kpsi, Sy = 60 kpsi, and Sut = 80 kpsi. The bar is…

A: Given:The endurance stress is The yield stress is The ultimate stress is The steady torsion stress…

Q: A solid shaft made of a ductile brass alloy is subjected to an array of loads, resulting in the…

A: Maximum shear stress theory Maximum shear stress theory is also known as Guest's theory. According…

Q: Q1: A motor driving a solid circular steel shaft transmits 30 kW to a gear at B (as shown). The…

A:

Q: (Q6) A solid spring steel shaft in small engine with 5hp at 3000rpm is used as a torque measuring…

A:

Q: 4. A bar of steel has minimum properties of Se=40 kpsi, Sy = 60 kpsi, and Sut = 80 kpsi. The…

A:

Q: hena) A hot-rolled steel shaft with a shoulder fillet is subjected to an axial load P which varies…

A: When a load or force is acting on an object in a way that it is parallel and on its axis then it is…

Q: Determine the allowable value of the torque, T, which can be applied to the solid circular shaft…

A:

Q: Problem 4.2 The stepped shaft shown in Figure below is subjected to a tensile load of 32 kN and to a…

A: Given: F=32 kNSut=830 MPaE=207 GPaT=150 NmSy=620 MPa

Q: hardest point in the embedment A or B of the element shown in the figure. This bar is made of hot…

A:

Q: A gear transmits 560 N of torque to a circular shaft having a diameter of 58 mm. A square key 13 mm…

A: Given Data The diameter of the shaft is: d=58 mm The torque transmitted by the gear is: T=560 N·mm…

Q: A drive shaft is made of solid steel. It is desired to transmit 2.5 hp at 150 rpm. The allowable…

A:

Q: 2 in in 1 in 8 3 in 3 in 3100 in in

A:

Q: ou A bar of steel has the minimum properties S,- 276 MPa, S,-413 MPa, and Sut 551 MPa. The bar is…

A:

Q: A circular cross  section shaft has a diameter of d = 45 mm, is subjected to a combined state of…

A:

Q: A mechanism used in a punchingmachinery consists of a tension spring assembled with a preload of 30…

A: GIven DataW=30Nd=2mmC=Dd=7n=10τ=780 N/mm2G=80kN/mm2

Q: For the solid shaft, 1 inch in diameter, subjected to bending and torsion, find the principal…

A:

Q: A shaft made of steel has the following minimum properties Se = 264 MPa, Sy = 413 MPa, and Sut = 536…

A:

Q: neter of the shaft from stat = 5. Bending moment and tion speed of the shaft if ed in the…

A: In horizontal Plane: Now TorqueA= (500-75) × 82                  = 1700 lb.in TA= TB   (Power is…

Q: A conditioned room contains 12,000 W of fluorescent lights (with older coil ballasts) and twelve 90%…

A:

Q: Two designs for a shaft are being considered. Both have an outside diameter of 60 m and are 800 mm…

A:

Q: A drive shaft running at 2500 rpm has outer diameter of 60mm and inner diameter of 40mm. The…

A:

Q: shows a round bar subjected to a bending load F = 0.80 kN, and axial tension P = 7.2 kN, and a…

A:

Q: 1. (Book Problem) A round steel bar having Sy = 800 MPa is subjected to loads producing calculated…

A:

Q: A solid 2.0 in. diameter shaft is used to synchronize multiple mechanisms in a manufacturing plant.…

A:

Q: The figure shows a section of a shaft made of annealed steel with yield strength of 600 MPa and…

A: Given: The yield strength of material, Sy = 600 MPa The ultimate strength of the material, Su = 700…

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.