Smooth pipe, diameter 0.19 m, length 12.1 m, and filled with SAE 30 oil. There is no change in elevation throughout the pipe. The pressure drop across this pipe is 327 kPa. Find the Reynolds number? Answer: 8523

Q: How did you solve for the velocity of b?

A: The given question was solved using velocity polygon method.If AB is a link which is rotating about…

Q: solve both

A: Power input, Gear speed of input shaft, Gear ratio, Power loss,

Q: What is the module of a spur gear with 30 teeth and pitch diameter if 5 inches? 5.236 mm 4.233 mm…

A: The given values are -  Teeth T =30 Pitch diameter D = 5 inch(127 mm)

Q: INSTRUCTIONS: Solve for all unknowns (magnitude and direction). A 10' 300# 10' 150# B 5'

A: According to the given data A beam  AB is given  We need to find Reaction  at point A and B

Q: 4 = 2, B= 3, and the angle formed by A and B is 60°. Calculate the value of 4+ 2B. Round your answer…

A:

Q: QUESTION 8 What is the specific volume of air at 184 K and 139.23 kPa? Give your answer in mkg to 3…

A: Solution is attached below:

Q: 2. From the given figure below, solve for the bar Y from the reference line. (choose the nearest…

A:

Q: R.75 00.63 THRU $5 01.123 0.250 E 1.38 0.63 mm radius hole partially through the part 0.63 mm radius…

A:

Q: 4. From the given figure, solve for the bar Y from the reference line . (choose the nearest answer)…

A:

Q: A Prony brake with a 12” arm is applied to an engine flywheel. At 1200 rpm, the scale registers 20…

A:

Q: Determine the mass of a steel ball whose diameter is 16mm.

A:

Q: 1500# 1500# 1500# 1500# 12' K I

A: In this problem, following steps will be taken 1. Determine the reactions at the supports.' 2. Using…

Q: Solve for the mobility. Show your logical and accurate solutions after every fig

A:

Q: The engine piston weighs 180 g. The machine speed is 4400 RPM. What is the maximum speed of the…

A:

Q: Using the figure below solve for the desired degrees to be set in the compound rest. I TPF = .602…

A:

Q: Solve the problems below: (Use 4 decimal places for all your computations) 1. A water tank 3 m in…

A:

Q: The result that I got after solving it was 463.0721, is that correct?

A: Given: d= 0.27in τ capacity=26.5 ksi = 26500 psi. Factor of safety =1.6 To find: The maximum T-force…

Q: The steel wide-flange beam has the dimensions shown. If it is made of an elastic perfectly plastic…

A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked .…

Q: why have you writen the answers in mm. when all the length are in meters

A:

Q: 1- Sketch front, right and top views of the following object. Each grid represents 10 mm. Front

A: Given: Sketch Front, top and right side view of the given isometric view.

Q: Q/Find the value of T (kN. m/m) So that the value of angle of twist at D equal to zero.

A: The elemental angle of twist for the shaft CD can be expressed as, On integrating the above…

Q: Express the quantity 254,998m in mm.

A: To convert meter quantity into millimeter one must be familiar with the no. of mm exist in one…

Q: 40 7 slug 110 dyne

A: given:

Q: many hours did the carpenter work on the job? 6. What is the area of a rectangular floor that is…

A: Q.6 Given data as per question Length of floor = 7’-3” Width of floor = 4’-2”

Q: A Tyrannosaurus named Rex was having a birthday. He was standing on one end of a cart that rolled…

A:

Q: o shafts 3679mm between centers carry pulleys 1288 mm in diameter and 910 mm in  diameter…

A: dL= diameter of larger pulley dS= diameter of smaller pulley C= distance between the centers of…

Q: can the solve the last three quetsions please

A: mass of refrigerant R-22, m= 2kgThe initial pressure, P1= 6.8 barThe initial state is saturated…

Q: 6. Three reservoir A, B and C are connected respectively with pipes 1,2 and 3 joining at a common…

A: Given:The elevation of the common junction D, The elevation of the reservoir A, The elevation of the…

Q: Where did you get the 3 from for the distance of q?

A:

Q: (5) In order to forge a pure gold ring, you first need to purchase the gold. The ring design is a…

A: According to Pappus–Guldinus theorem volume can be given as V=Ax2π×yArea of the block as per given…

Q: A piston engine in which the bore and stroke are of equal dimension is referred to as a "square…

A: Given:Let bore be 'D' and stroke be 'L'For a square engine, D = LNo of cylinders, n = 8Displacement…

Q: Solve it Properly and with right answer.

A: Case-1 Given data: The inside diameter is, di = d. The outside diameter is, do = 1.5d. Calculate…