Sketch the titration curve that will be obtained when 50 mL of 0.05 M glycine at pH 1.5 is titrated with 0.05 M NaOH at 25°C on the graph provided below. In your graph, show (i) the position of the initial pH of the solution before NaOH is added, (ii) the ½ equivalent point 1, (iii) the 1* equivalent point, (v) the position and value of the pl (vi) the second ½ equivalence point and (vii) the endpoint of the titration. Remember to also indicate the volume of NaOH at these key points in your curve. Be as accurate as possible.

Sketch the titration curve that will be obtained when 50 mL of 0.05 M glycine at pH 1.5 is titrated with 0.05 M NaOH at 25°C on the graph provided below. In your graph, show (i) the position of the initial pH of the solution before NaOH is added, (ii) the ½ equivalent point 1, (iii) the 1* equivalent point, (v) the position and value of the pl (vi) the second ½ equivalence point and (vii) the endpoint of the titration. Remember to also indicate the volume of NaOH at these key points in your curve. Be as accurate as possible.

Chemistry

10th Edition

ISBN:9781305957404

Author:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan A. Zumdahl, Donald J. DeCoste

Chapter1: Chemical Foundations

Section: Chapter Questions

Problem 1RQ: Define and explain the differences between the following terms. a. law and theory b. theory and...

See similar textbooks

Similar questions

Do not give answer in image and hand writing
The following table shows the values of ionization constants for a number of acids and bases at 25 °C: Formula Ka HC2H302 1.8x10-5 HCIO2 NH3 HCIO 1.1x10-2 2.9x10-8 Kb 1.76x10-5 For the best system, calculate the ratio of the masses of the buffer components required to make the buffer. Express your answer to two significant figures. PH = 7.30
How is activity related to the 1/2 equivalence point in a titration? activity=activity coefficient x Molarity
We add 10mL of 0.1M NaOH to 100mL of 0.1M CH3COOH/ 0.1M CH3COO^-. (Ka = 1.8 x10 ^-5). Using the Henderson-Hasselbach equation, pH=pKa + log [A-]/[HA] a) before the addition of NaOH b) after the addition of NaOH
In an acid-base titration, a base or acid is gradually added to the other until they have completely neutralized each other. Since acids and bases are usually colorless (as are the water and salt produced in the neutralization reaction), pH is measured to monitor the reaction. Suppose that the equivalence point is reached after approximately 393 mL of a NaOH solution has been added (enough to react with all the acetic acid present) but that replicates are equally likely to indicate from 373 to 417 mL (exclusive), measured to the nearest mL. Assume that two technicians each conduct titrations independently. What is the probability that the average volume at equivalence from the technicians is 416 mL or 417? Select one: O a. 0.79069767 b. 0.00000000 c. 0.00054083 d. 1.00000000 e. 0.00049383 f. 0.02941176 O g. 0.04651163 O O
MISSED THIS? Read Section 18.4 (Page); Watch KCV 18.4B. Consider the curve shown here for the titration of a weak monoprotic acid with a strong base. Hd 14 12 10 8 6420 80 120 160 40 Volume of base added (mL) The figure shows pH as a function of volume of base added. The pH is measured from 0 to 14 on the y-axis, while the volume of base added is measured from 0 to 160 milliliters on the x-axis. The curve of the plot goes up gradually from pH 2.3 at 0 milliliters to pH 5.8 at 49 milliliters, next the plot goes up steeply to pH 11.8 at 51 milliliters, and finally the plot goes up gradually to pH 12.2 at 160 milliliters. ✓ Correct An equilibrium problem based on the initial concentration and Ka of a weak acid should be solved for aqueous solution of the weak acid. This is true for the initial state of titration, when no base has been addition of a small amount of a strong base turns this solution into a buffer whose pH is calculated in way. Part D At what volume of added base does pH =…
When titrating 25 mL of an approximately 0.1 M solution of a triprotic acid solution with 0.1052 M NaOH, a student calculates that the end point will be reached after the addition of approximately x mL of NaOH. However, after the addition of 2x mL of sodium hydroxide, no colour change is observed. Which of the following errors could not account for this obervation? using a 3 mole acid : 1 mole base ratio in the calculation washing the sides of the flask with DI water during the titration and diluting the analyte solution mistakenly using a 0.01000 M NaOH solution in the titration failing to add an indicator to the analyte solution mistakenly using a primary standard solution of > 1.0 M in the titration
A 150 mL solution of NaOH is titrated with HI. Phenol red is the indicator, which is red at high pH values and yellow at low pH values. The indicator be [ Select ] when you first put it into your analyte, before any titrant is added. The indicator will be [ Select] at the endpoint. The indicator will be [Select] V if you overshoot the endpoint and add too much acid.
Construct a graph and plot the titration curve for a 10.0 mL aliquot of 0.100 mol/L NH3 (pKb=4.74) with 0.100 mol/L HCl. For this purpose, make a table with nine added volumes of HCl solution, which you consider adequate, with the corresponding pH value. Write the development of all calculations and use approximate formulas.
Please help explaining this one. For 270.0 mLmL of a buffer solution that is 0.270 MM in CH3CH2NH2 and 0.195 MM in CH3CH2NH3Cl, calculate the initial pH and the final pH after adding 0.030 mol of NaOH. Kb(CH3CH2NH2)=5.6×10^−4