Sketch the output voltage against time diagram for the values given in Q4 in the following cases: a) Vin is a sine wave with peak-to-peak voltage of 8 V and period of 5 ms. b) Vin is a sine wave with peak-to-peak voltage of 4 V and period of 5 ms. +Vs Vin A Vout V. T-Vs R2 + |R, Vref Figure 2

Q: For the circuit shown in the following figure. The output voltage is equal to-- -2 V a Vout O a1V •…

A: The given circuit is   As the op-amp circuit is open-circuited, means there is no feedback present,…

Q: Consider the circuit of Figure 1, with a periodic square signal voltage source at a frequency f=500…

A: To solve the circuit, we can use Kirchhoff's voltage law (KVL) and the differential equation…

Q: With capacitors in this Inverting Op-Amp, how should I find worst case values of Rin and Rf?

A:

Q: Exercise 2: Buck Converter Design: Design a buck converter to produce an output voltage of Vo=18 V…

A: It is asked to design a buck converter for the given values of input and output voltages. We need to…

Q: Refer to the circuit in Figure Q2. Sketch and label the input voltage, Vi and output voltage, Vo. Vi…

A: In this question We need to determine the input and output waveform.  We know Vo /Vi = -100

Q: 1.Sketch the output voltage against time diagram for the values given in Q4 in the following.  Vref…

A: The circuit diagram is shown below, Where,Vref = 2 V,  Vs = 10 V  R1 = 1000 Ω R2 = 10,000 Ω

Q: Q1 Analyse the circuit shown in Figure Q1, (а) Name the function of each Op-Amp, A1, A2, A3, and A4…

A:

Q: An op-amp comparator in a firing circuit can produce waveforms at the output of up to 30 V…

A: A direct current voltage source with negative and positive terminals attached to the first and…

Q: Q2.Find Q-point when VBB = 1V, 2 V and 3 V.. Assume VCE(sat) = 0 V. Ro 1.0 KM www Bpc = 50 10 V 20…

A: We need to find out the current and voltage for given circuit.

Q: An op-amp has a slew rate of 0.8 V/us. What is the maximum amplitude of undistorted sine wave that…

A:

Q: Q3( (A) Consider you have to analyze a Step-Down DC convertor having the following parameters: Input…

A: "Since you have posted a question with multiple questions, we will provide the solution only to the…

Q: Consider the following step up converter with a resistive load of value R-5 ohms. It is supplied by…

A: Consider the following step up converter with a resistive load of value R=5 ohms. It is supplied by…

Q: Q3 Thermistor is a resistive temperature element made from semiconductor materials such as oxides of…

A: The thermistor is a negative temperature coefficient device The temperature at the 0 c of the…

Q: One way to measure the slew-rate limitation of an op amp is to apply a sine wave (or square wave) as…

A: Given  Frequency of input sine wave is f =1 MHz The peak to peak amplitude of  output wave form is…

Q: The buck converter with resistive load has the input voltage of 30[V], the output voltage of 20 [V]…

A:

Q: Determine the output voltage due to VDCoffset. Include a schematic of your circuit. Determine the…

A:

Operational Amplifier

An operational amplifier also called op amp is an integrated circuit or analog circuit that takes input as a differential voltage and produces output as a single-ended voltage. It is an IC that can amplify weak electric signals.An op amp has one output pin and two input pins. The basic role of an opamp is to amplify the voltage difference between the two input voltages. It is also used in filtering or to perform mathematical operations or in signal conditioning.