Consider the following step up converter with a resistive load of value R-5 ohms. It is supplied by a DC power source of magnitude Vs-200 V. The switching frequency is 5 kHz and the duty cycle k is first set to 0.5 and the inductance used within the circuit has a value of L-10 mH. The switch is supposed to be ideal. The minimum current in mode 1 is: Select one: O a. 11 = 81 A O b. 11 = 100 A c. 11 = 79 A O d. 11 = 75 A

Consider the following step up converter with a resistive load of value R-5 ohms. It is supplied by a DC power source of magnitude Vs-200 V. The switching frequency is 5 kHz and the duty cycle k is first set to 0.5 and the inductance used within the circuit has a value of L-10 mH. The switch is supposed to be ideal. The minimum current in mode 1 is: Select one: O a. 11 = 81 A O b. 11 = 100 A c. 11 = 79 A O d. 11 = 75 A

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter21: Resistive-capacitive Series Circuits

Section: Chapter Questions

Problem 7RQ: An RC series circuit is connected to a 120-V, 60-Hz power source. The resistor is 25 and has a...

See similar textbooks

Similar questions

C'uk Converter Design A C'uk converter has an input of 12 V and is to have an output of - 24 V supplying a 60 W load. Select the duty ratio, the switching frequency, the inductor sizes such that the change in inductor currents is no more than 12 percent of the average inductor current, the output ripple voltage is no more than 1.5 percent, and the ripple voltage across C1 is no more than 3 percent.
A step down converter is operated with a duty cycle of k = 0.75. The input voltage is Vs = 20V, and the load is: L = 5mH, R = 1502. The minimum inductor current is I₁ = 0.1A. The maximum inductor current is: Select one: a. 1.9 A b. None of these OC. 0.9 A O d. 1.1 A Oe. 2 A
Design a Cuk converter that has an input of 25V and the output of -30V. The load is 60W. Specify the duty ratio, switching frequency, inductor values and capacitor values. The maximum change in inductor currents must be 20 percent of the average currents. The ripple voltage across capacitor C1 must be less than 5 percent, and the output ripple voltage must be less than 1 percent.
The anode of a diode is connected to one terminal of a 1-KΩ resistor. The other terminal of the resistor is connected to the ground and the negative terminal of a 12-volt DC source is also grounded. The three components are connected in series. How much is the load current with the ideal diode?
A semi-converter with RLE load and a freewheeling diode has discontinuous load current with firing angle a and extinction angle ß. The freewheeling period is O a. B-T O b. TT- a O c. TT+ a O d. B - a
Q6) The waveform of the voltage obtained after rectification is of a -----nature and therefore contains .harmonics a. Sinusoidal O b. Triangular c. Pulsating O d. Repetitive O
6. The R-C circuit has a resistance of 100 ohms and a capacitive reactance of 150 ohms are connected in series across a A.C. voltage source. If a current of 0.9 A is flowing in the circuit determine (a) Power factor (b) Active power (c) Reactive power.
A step down converter is feeding an inductive load with R-10 Ohms, L15 mH and E-1sV. The supply is Vs-200v, the switching frequency is 10 kHz and the duty cycle is k-0.5. The maximum peak to peak ripple current in the load is equal to 0.34A. The erage load current la would be equal to: Select one: a. 8.5A O b. 18A Oc 11A O d. None of these
An R-L load is connected to a 250 V, 400 Hz step down dc converter. The average load current is 100 A. The load resistance is 0.5 Ohm. The allowed ripple limit is 15%. The minimum value of inductor to limit the maximum ripple current is:
ew1
The DC-DC converter below is fed from a 96 V DC source and it is desired to obtain a 24 V output voltage on a 15 ohm load resistor. The switching frequency of the converter is 50 kHz. It is desired that the fluctuation rate in the output voltage should not exceed 1%. What is the minimum coil inductance and minimum capacitor value?
2.A Boost converter has an input voltage of 5V and required output voltage is 15V at 25KHzwhen L=150µH and C=220µf and average load current of 0.5A.Determine i) Duty cycle ratio ii)peak to peak ripple current through inductor iii) peak to peak ripple voltage iv) critical values of L & C