Sketch the OBLIQUE drawings based on the ORTHOGRAPHIC views. *₁ 2. *** TOP FRONT A A A RIGHT SIDE ENGINEERING NAME: GRAPHICS FILE NO.:: K SECTION: A CAVALIER OBLIQUE GRADE OBLIQUES OBL-1

Q: 38 17 Hole Tam delik 18 19 20 20 8 26, 20. 89

A: Given:-

Q: 2 - Explain the bonding, hybridization and geometry of carbon nanotubes that are used to help store…

A: Introduction: carbon nano tubes are in the form of cyliders. It can be made by the graphine sheet by…

Q: Below are incomplete views of the parts or figures. Complete them by drawing the lines of…

A: Given:Find:Draw the lines corresponding between the views.

Q: Engineering Application Near the top of the Citigroup Center building in New York City, there is an…

A: Given data: m=4.6×105kgt=2 sd=2 m Need to determine the spring force constant and energy stored by…

Q: For the mechanisms shown below determine the number of links, full joints, half joints and the…

A: “Since you have posted multiple questions, we will provide the solution only to the first question…

Q: Water at 10°C flows through the system shown in the figure below at 0.28 m³/s. Energy loss in the…

A: Temperature of the water vessel. T1=10°C Diameter of the pipe. d =30cm=0.3m Diameter of the pipe…

Q: A) Draw the two limiting positions of the following crank-slider mechanism. Indicate all known sizes…

A: Given:To find:(a) Draw the two limiting positions.(b) Determine the piston stroke.

Q: Draw chalk diagram of all sections

A: To draw section views

Q: Determine the Moment of Inertia for the cross-section shown about the centroidal axis. Given M=IS…

A:

Q: Another name for "SIZE DESCRIPTION is: 37 A Dimensioning B Orthographic projection. C Assembly…

A: Given Engineering drawing To find Size description Leader line Extension line

Q: To make the 3d sketch for each of the frames which contain the views in the plan

A:

Q: The boom ABC in Fig 4 is held by the ball and socket joint at A and the two cables EBF and CD, as…

A:

Q: ➤ Consider FBD of pulley H: F₁, FH 54" Y TBF = 0.2666053799P = 500N TGF = 0.43137655663P = 500 N By…

A:

Q: 1

A:

Q: elow are incomplete views of the parts or figures. Complete them by drawing the lines of…

A: According to the given dataAn orthographic projection view is given.We need to findmissing view of…

Q: he Lookout Hills gravitational slope-deformation feature in Bonne Bay, western Newfour plume of rock…

A: 306m wave height has been found in norris point.

Q: Answer the attached file

A: The diameter of the pipe between pump and reservoir is D1=20 cm. The length of the pipe pipe between…

Q: Estimate the flow rate Q of water discharging from the nozzle as shown in Figure 3. If the fluid…

A:

Q: O₁ and O₂ are the fixed link in the mechanism which is 3.25" away from each other in a vertical…

A: To Find:The velocity of the slider C when the position of the crank is Given:

Q: A 20 straight-tooth bevel pinion 32-tooth gear. The two shafts are a (a) The cone distance (b) The…

A:

Q: To make the circle in an Isometric drawing which geometric option we select from menu bar and why?…

A: 1.To make an isometric drawing of circle we select it from menu bar because we do not have any…

Q: Match the following in the right order

A: Given below solution Explanation:Step 1: Step 2: Step 3: Step 4:

Q: The force F shown below is applied in the positive x-direction against a 20-degree slope. The force…

A:

Q: Orthographic view of the following sketch

A:

Q: General Questions Not Directly Print Related) 1.  ____________use conventional symbols with single…

A: Fill in the blanks

Q: Make an orthographic projection.

A: The orthographic views for the given isometric object are drawn below with the actual scale 1:1

Q: In creating orthographic views, each view must:

A:

Q: The figure (not to scale) shows a representation of a hoisting system. A couple is applied to the…

A: Initial angular velocity of A, Final angular velocity of A, Time interval

Q: Draw the three standard orthographic views for the following object.

A: Draw the three standard orthographic views for the following object.

Q: A square steel plate is perfectly insulated above and below, so the only heat flow is through the…

A: Given: To find: Temperatures inside the steel plate

Q: Use the below information to answer Questions 12 – 13. A uniform bar, of mass M, with seven evenly…

A: Task 1 If two cylinders can be added to the system, which two holes should the two cylinders be…

Q: An engineer is making an estimate for a home owner. This owner has a small stream (Q = 0.05 m³/s)…

A: The given information in the problem is represented in the following attached image:

Q: The height of an object would be found on which  of the standard views in a set of drawings

A:

Q: If the compact disc is spinning at a constant angular rate 0 = 355 rev/min, determine the magnitudes…

A:

Q: sketch the 2d figure using autocad and colour the hatching and reference lines

A:

Q: DRAW THE ISOMETRIC FIGURES OF THE ORT

A: According to the details provided in the question, we need to draw an isometric view

Q: 1. In the given figure, gear 1 has 24 teeth and gear 2 has 70 teeth of PD=4. Gear 3 has 20 teeth and…

A:

Q: For the objects shown in orthographic projection below, construct an isometric Use the box method to…

A: Find Isometric view of the object.

Q: To create a Polyline or Polygon geometry object, which two objects must first be created?

A: A polyline is a connected sequence of a line segment created as a single object and a polygon is a…

Q: I just need help drawing the KINEMATIC DIAGRAMand the GRAPHS (v-a, a-s, s-t, v-t, v-t, or a-t) if…

A: Given: The v-s diagram is shown below: From distance 0 to150 m, the equation of velocity line is…

Q: Finish the Orthographic drawing

A: Please refer the following Front view, right hand side view and top of the given isometric view. 1…

Q: SPECIFY WHERE DIMENSIONS NEED TO BE PLACED FOR THE FOLLOWING PART NOTE: JUST NOTE WHERE…

A: To mark the letters on the following figure mentioned.

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.