Make an orthographic projection.

Q: 38 17 Hole Tam delik 18 19 20 20 8 26, 20. 89

A: Given:-

Q: (b) During a certain machining experiment at the UCSI workshop, it is observed that temperature at…

A: (i). In a metal cutting process, Maximum heat is carried out by chip then tool and lastly by the…

Q: draw the orthographic view of the drawing and identify the alphabets of lines used by pointing out…

A:

Q: Draw the orthographic Projections of given object. $30 080

A: The orthographic projections of the object include Top View, Front View, and Side View. All…

Q: Write a CNC program code to machine this part.

A: Since the part is symmetrical, thus divide the given component into half and the half part.

Q: Complete the orthographic drawing

A: If we plot isometric view, it looks like below

Q: Sketch the orthographic view

A: Solution: The front, top and side views are shown below:

Q: Draw the orthographic Projections of given object.

A: Orthographic projection is used to represent the 3 Dimensional objects into 2 dimensions,Usually the…

Q: Draw velocity polygon.

A: Solution:

Q: Ø60 60 ALL DIMENSIONS IN mm R15 18 120 36 14 DRAW THE 3RD ANGLE ORTHOGRAHIC PROJECTION & ISOMETRIC…

A: Isometric drawing is given, Draw the orthographic projections.

Q: 1. Determine the tolerance allowed on the hole of the part.

A: Tolerance – the total allowable change in measurement; the contrast between the upper and lower…

Q: Draw the three standard orthographic views for the following object.

A: Draw the three standard orthographic views for the following object.

Q: In an orthographic projection of a figure that is a single block high, which two sides are congruent…

A: in an orthographic projection of single block high, front and back sides are congruent figure, top…

Q: Sketch the OBLIQUE drawings based on the ORTHOGRAPHIC views. *₁ 2. *** TOP FRONT A A A RIGHT SIDE…

A: To draw: The oblique view. Given: The front, top, and side views are shown below.

Q: Stainless steel 316 pin fins are designed for use in industrial cooling. The fins will be subjected…

A:

Q: Draw the figure with projections

A: Draw the figure with projections

Q: Finish the Orthographic drawing

A: Please refer the following Front view, right hand side view and top of the given isometric view. 1…

Q: 1. A rotating cylinder viscometer was used to find the dynamic viscosity of SAE 10W-30 oil at 130°F.…

A: To find: The dynamic viscosity of SAE, and also find the power required to rotate the cylinder at 50…

Q: Problem 2) As a result of loading, the rectangle with a = 25 mm and b = 18 mm deforms into a paral-…

A:

Q: L HRP FRP (TOP VIEW) (FRONT VIEW) L (RIGHT SIDE VIEW) L

A:

Q: 45 TV Ø55 $30 4-018 15 11 ED R10 15 FV 50 41 RSV 42.5 100 142 21 85

A: First, we have to understand what is orthographic view; orthographic view is a technique to…

Q: State any three rules of orthographic parallel projection.

A: Orthographic parallel projection is a method of representing 3D objects normally by three 2D…

Q: Draw the 1st and 3rd Angle Orthographic sketch of the following part:

A: According to the 3d object provided in question three orthographic view is drawn with the help of…

Q: draw the isometric view of the drawing identify the alphabets of lines on the orthographic view

A: Find Isometric view of the object

Q: Problem 1. Using Solidworks, make a 3D solid model of the part shown below. (Exercise 6.11, Page 272…

A: I have attached the images showing step by step creation of the 3D model .

Q: = Compressive Force the connecting Rod EE Piston Effort 120 Guide Force Fig. P-1 Fie. P-2 Tools: sin…

A: let be the mass of D is mD and angle from crank A is θ. Draw the free body diagram.   Apply force…

Q: Use Share Sketch to create this part with one sketch. Pivot lock (dimensions are in inches. The…

A: Below is the sketch of the part using share sketch.

Q: A flanged bolt coupling consist of six 10 mm. diameter steel bolts on a bolt circle 300 mm. in…

A:

Q: -50- .38 6X Ø.25- .125 R.05 TYP 2.00 2.50 3.00 1.00

A: Isometric view to orthogonal view :

Q: 3. An octahedron of sides 50 mm lying on the HP on a face such that one side of the face which is on…

A:

Q: At a point in a strained material, if two mutually perpendicular tensile stresses of 200 kg/cm² and…

A: A stress element is given as shown-Tensile stresses-Also, To Find-The tangential stress on the 15o…

Engineering Drawing

Technical drawing has been around since ancient times. As in the ancient Renaissance, complicated drawings were created, including Leonardo da Vinci's drawing. Modern engineering drawing, including its specific orthographic projection with scale conventions, began in Europe (France) during the early stages of Industrialization. L.T. C. Rolt also made some of Marc's drawings for its block-making machinery (in 1799) that also may have contributed significantly to British engineering technology. Since he learned the art of presenting three-dimensional(3D) items in a two-dimensional(2D) plane, as we now term mechanical drawing.