Sketch the compressive funicular structural forms ("arches") for each of the two structures below to support the loading patterns indicated. The funicular structures must rest on the two hinged supports and pass through the red dot. Ignore the effect of dead load. Note- these can also be drawn "upside down" as cables. (the dotted lines are for your convenience)

Q: Current Attempt in Progress A compound shaft consists of brass segment (1) and aluminum segment (2).…

A: Given Data  TC = 19400 Nm = 19400 × 103 Nmm  Allowable shear stress in brass = 53 MPa Allowable…

Q: 1. Determine the maximum moment and maximum shear of the following beams. Draw the Shear and Moment…

A:

Q: Answer correctly ty

A: i) divide the length of the gutter by the effective width covering of one sheet , refer to the…

Q: Situation 3] A 46X.0-m long boundary line is to be laid out with a 30.0-m invar tape weighing 0.70…

A:

Q: Determine the centroid of the shaded area shown, which is bounded bythe X axis and the parabola y? =…

A:

Q: The cantilevered beam with fixed end support at A and rollers at B and C respectively, it carries a…

A:

Q: Water flows through the curved pipe shown in the figure below where point X denotes the center of…

A: Given: The discharge is 1 m3/s. The diameter of the pipe at the inlet is 0.5 m. The diameter of the…

Q: 2. A suspension of particles with a particle density of 2796 kg/m³ is settling in water with a…

A: Given Specific gravity G = 2796/1000 = 2.796  Kinematic viscosity of water at 20 ° C = 1.004 × 10 -6…

Q: Problem Solving: 1. The details of the cantilever beam are shown below. Use f'c = 28 MPa, fy = 415…

A:

Q: A 0.375 -in. thick rectangular alloy bar is subjected to a tensile load P by pins at A and B. The…

A: Given data in question  Load 11 kips Thick 0.375 inch Height 3 inch Strain in longitudinal and…

Q: 7-126 The maximum flow rate of a standard shower head is about 3.5 gpm (13.3 L/min) and can be…

A: Solution: Given: maximum flow rate = 13.3 L/min Reduced flow rate = 10.5 L/min Number of persons = 4…

Q: Determine the flexural stress at point A (in MPa) given that the bending moment applied to the…

A:

Q: Problem For a given sol, the following are known, G, = 2.70, moist unit weight is 20.3067&N /m², and…

A:

Q: 8. Determine the magnitude and coordinate angles of the resultant force acting at A. daB dac R in…

A:

Q: A roof system consists of W14x30 beams with a span of 12 ft and a tributary area of 144 ft?. The…

A: The dead load is D=45 psf. The snow load is S=27 psf. The rainwater/ice load is R/I=34 psf. The wind…

Q: In the given figure, the 280 lb-bar AB is 10 ft long and hinged at B. It rests upon a 400N- block at…

A:

Q: 1O N A GN

A:

Q: Determine the minimum force P to prevent the 399-kg rod AB from sliding. The contact surface at B is…

A: Take moment about B:∑ MB=0NA3+fA4-mg42=0NA3+0.45NA4-399×9.8142=0NA=1630.9125N

Q: A simply supported beam with spans of LAB = 8 ft and LBc = 24 ft supports loads of w = 4.5 kips/ft…

A: Maximum shear stress and Maximum bending stress in the beam.

Q: An essential 5-story facility structure is conceptualized with an intermediate reinforced concrete…

A:

Q: 10.73 An engineer is making an estimate of hydroelectric power for a home owner. This owner has a…

A:

Q: QUESTION 14 A non-potable water storage tank is at an elevation of 37 feet above the discharge for…

A:

Q: Calculate the Shear Force at point A of the following Beam. Take X=35 kN and Y=80KN YKN X kN/m A, D…

A: Given, Beam,

Q: Problem 1a. Determine whether each of the beams and frames below are internally determinate,…

A: No. of reaction = (3 for fixed 2 for hinge 1 for roller)  a.)No. of Reaction = 4 (2+1+1) (2 for…

Q: 1. For a constant head laboratory permeability test on a dine sand, the following values are given:…

A:

Q: An earth embankment requires 2000 m of soil for construction at a target dry density of 17 kN/m.…

A:

Q: Use Area-Moment Method. E = 200 GPa and I = 90 x 10® mm“. Determine the rotation at A in degrees.…

A: Solution:- The given diagram is shown below,

Q: 3. Which of the following is NOT a measure of forecasting errors? A. Mean absolute error (MAD) B.…

A: Explanation : Forecasting error is the discrepancy between actual and predicted demand numbers.…

Q: 8. Compute the AL and the Ad for each leg of the traverse shown below. Show the EL and the Ed as…

A: Lattitude and departure signs :  N-E : Both positive  S-E : Lattitude negative Departure positive…

Q: Problem 2 Determine the moment of the force 360 N about points A and B. 360 N 40° 100 mm 225 mm A

A: To find :- Moment of 360 N about point A and point B

Q: a ga in tension with the following results: Applied 1 Strain Force (N) (mm) (%) 0 5.000 Stress (MPa)…

A: We…

Q: Highway curve has R = 800 m, I = 20° 00', and Pl station 3+290.600 m. Part A Determine degree of…

A: R=800mdegree of curvature=?

Q: In what type of building code article would you see a statement describing in detail the nailing…

A: QUE:- in what type of building code article would you see a statement describing in detail the…

Q: A composite beam is under external loads as shown below. a) Draw the internal shear force and…

A:

Q: 7 1) 4)| Which of the following is true regarding the Moment- An internal hinge for the conjugate…

A: As per bartleby policy I can answer only 3 true/false question at a time. please re-upload again the…

Q: For the built-up section shown, determine the following: a. Centroid of the Area, b. Moment of…

A:

Q: Set up the appropriate equation that is used to solve for the moment of inertia about the y axis.…

A:

Cables

Cables are collections of wires, alternatively referred to as a cord, connector, or plug. They are one or more wires covered in a plastic covering that allows for the transmission of power or data between devices. The earliest use of recognizable electrical cable was the early commercialized telegraph lines. These were iron-made and tedious to produce and install cabling.