A Click Submit to complete this assessment. Question 5 At what Horizontal Distance (HD) in feet from the rod is the Point of Instrument (PI) -7 3 -6 -5 T C

Q: Hand

A:

Q: Use the virtual work method to determine the vertical deflection at joint C of the truss shown. 15…

A:

Q: -tested in an uncons ssure of 200 kPa and

A: Given: Effective shear strength parameters c'=20 kPaθ'=25o Cell pressure is 200 kPa Principal stress…

Q: 1) For a falling head permeability test, the following are given. Determine the hydraulic…

A: The falling head permeability test is performed to determine the hydraulic conductivity of a soil…

Q: Q- Calculate the corrected staff reading at point A, if the staff reading is taken from an…

A: Given :- instrument distance from point A ( d )= 1.5km Staff reading at point A = 3.46 m Corrected…

Q: - A uniform beam (EI= constant) PQ in the form of a quarter-circle of radius R is fixed at end P and…

A:

Q: A trapezoidal concrete-lined ditch has a bottom width of 3 depth of 2 ft, and side slopes of 2:1.…

A: Assuming Manning's coefficient (n)= 0.015 for concrete lined channel Bottom width (B)= 3ft Depth of…

Q: Using the Leveling Template set up and complete the differential level notes for the information…

A: A slope on which differential levelling has been carried out.To make differial level notes use…

Q: Take P₁= 5 kip and P₂ = 2.5 kip. (Figure 1) Figure 1 of 1 |||| Determine the absolute maximum shear…

A:

Q: ▼ The towline exerts a force of P = 4 kN at the end of the 20-m-long crane boom (Figure 1). Part A…

A: Force, To find:           (a) Distance (x) to create maximum moment.           (b) Direction of…

Q: 2. The Force system shown in Figure has a resultant of 300 lb up along the y-axis. Compute the…

A: Resultant force R=300 lb is acting upwards,Resolving forces…

Q: Problem 1 The boom is intended to support two ve cable CB can sustain a maximum loa determine the…

A:

Q: Determine the force in each member of the truss. State if the members are in tension or compression…

A: Given:Required:Force in each member of truss

Q: st unit weight of soil, gamma = 134 pcf factor of safety, FS = 3 quare footing carries the proposed…

A: As per the honor code, We’ll answer the first two question since the exact one wasn’t specified. So,…

Q: Problem 3: Derive the formula for the maximum deflection of a cantilever beam with span L loaded by…

A:

Q: A propped cantilever of span L is carrying a vertical concentrated load acting at midspan. The…

A:

Q: Determine the forces in all bars of the truss shown in the given figure. Indicate tension or…

A: Given TrussLoading 40, 30, 20 and 18 kNTo find out Member forces

Q: Using the method of joints, determine the force in each member of the truss shown. Summarize the…

A:

Q: Construct the specific energy and specific force curves for a 5 - ft - wide rectangular concrete…

A:

Q: The beam has a pin support at A and a roller support at B and is subjected to the loading shown.…

A: Given:Required:Maximum deflection

Q: The following column subjected to point loads is in equilibrium. Determine the reactions VB, HB and…

A: Given data,column fig is given FIND

Q: A sample of gray silty clay has a mass of 126 kg. Laboratory tests results give a moist density ()…

A:

Q: Q1 constant. Determine the slope and the displacement at C. El is 12 k-ft JA 4 ft 6k 6 ft B

A:

Q: CASE 1 E D. P P CASE 2 A DA F Họ K 8.

A: Member DG,BD

Q: A group of 16 piles are arranged in a square pattern and installed in a deposit of soft clay. The…

A: Ultimate capacity of pile is the sum of bearing capacity and friction resistance. For friction pile…

Q: P12.4. (a) Draw the influence lines for reactions MA, RA, and Rc of the beam in Figure P12.4. (b)…

A: (a) Draw the influence lines for reactions MA ,RA and Rc of the beam in Figure P12.4. (b) Assuming…

Q: 4 kN 7 kN-m 2m 3m 6 kN 5m 5 kN 2 m B For the beam shown on the left: Find reaction forces a) b) Find…

A: due to mistakes  i just re write  the value plz  don't  mind else i have to cut the entire  diagram…

Q: A +4.90% grade meets a +1.55% grade at station 4+200 and elevation 605.568 m, 195-m curve, stakeout…

A: To calculate the station elevations, an equal tangent parabolic curve is given with the following…

Q: 1. An electric field of 8.50 x 105 V/m is desired between two parallel plates, each of area 35.0 cm2…

A:

Q: How many acres are in the shaded areas in each example below? 000 640 160 320 40 N1/2, sec 25.

A: To find: How many acres are in the shaded areas?

Q: The picture below presents a system of four pulleys that will be used to lift a weight of G = 200N.…

A:

Q: Influence Lines for Determinate Beams. Use the tabular/equation approach to draw the quantitative…

A:

Q: A trapezoidal channel has a bottom width of 4.7 m and side slope of m=1.8. If the critical depth is…

A: bottom width=4.7mm=1.8critical depth=1mflow rate=?

Q: The scale of an aerial photograph is 1cm = 400m. The photograph size is 20 cm x 15 cm. if the…

A: Given: The scale of aerial photograph is 1 cm = 400 m S=400 m. The photograph size is 20 cm × 15 cm.…

Q: Problem 30: A percel of land is to be developed into 4-acre-lot single family housing. Historical…

A: Time of concentration, Tc = 7.5 minARI is 10 year storm

Q: The shear stress distribution for a circular section of diameter 'd' under the action of shear force…

A: Given:- The shear stress distribution for a circular section of diameter 'd' under the action of…

Q: 3-14. Determine the force State if the members are in F

A:

Layout and Design

The layout is the process of marking all the building components on the land from the prepared plan. The layout of construction includes transferring the whole plan of foundations, boundaries of the structure, centerline of the wall, and all other important structural parts on the ground along with the length and width so that the components of buildings can be excavated properly. Designing is the process of establishing the concept of the building on paper in a properly engineered manner.