sketch of elevation of this column using these details. (sample sketch of column below)

Q: (a) Draw the dimensioned plan and elevation for the given line plan. Assume all suitable data. (b)…

A:

Q: Locate the X-X centroidal axis for the cross section shown. £ sym. W840 x 329 W530 × 72 X X

A:

Q: In creating orthographic views, each view must… A. Preserve orientation between adjacent views and…

A:

Q: Choose the correct front view for the given drawing

A: i drawn rough sketch of front view   see it in below step

Q: What is the length of the vertical piece halfway between C and D in feet? B 12'-0" A 16'-0" D 16'-0"…

A:

Q: 42.) Which type of drawing can be used to show three sides of a solid from a comer view? an…

A: Isometric drawing is defined as that type of 3D drawing which draw the object in three dimensions.…

Q: Section lines are spaced from /16" to /8" or more apart. O True O False Section lines are normally…

A: Question 1 Solution: Section lines are usually drawn in order to understand the plane where the…

Q: Make a step by step procedure on how to determine area of irregular figures and or shape.

A: Some unusual features are made up of rectangular or square circles. The locations of those odd…

Q: how did they get grid 1-4 under beams ?

A: Solution: For beam the X and Y are the cordinates where the moment are to be calculated: Grid X…

Q: A4-ft-wide long footing is located at the top of a slope whose inclination is 30°. The soil of the…

A: The given data is shown below

Q: What is orthographic view elaborate? Draw orthographic view of the given figure assuming any…

A:

Q: If a standard view in a drawing has hidden lines, then creating a sectional view is always…

A: Sectional view represents the internal configuration of any object. It shows the details of all…

Q: Does the solution for part a really end once the sketch for the tied column is drawn. Dont you have…

A: Yes, the solution part is completed once the dimension and reinforcemnets are computed and drawn.…

Q: B) What is the difference between Spaced Sheeting and Close Sheeting

A: Solution: Closed sheeting is defined as the continuous frame having vertical and horizontal…

Q: The value of the smallest division on the main scale of a horizontal circle is graduated to 1/3…

A:

Q: Using a convenient scale, manually plot the following technical descriptions. Label your sketch…

A: Given : technical description

Q: Draw the front, Side and top

A: For this, we can draw the diagram in Autocad. I have used the same to draw the diagram and have…

Q: Draw the figure below in AutoCAD, take a screenshot of your work and paste it to the spaced…

A: The following image shows the given figure drawn in autocad with dimensions along with name.

Q: 10. 45 8.3 SUPPORT BRACKET 100 33 10 10 25 -

A: Question being asked here is to draw the ISOMETRIC VIEW for the given projections And the given…

Q: Compute the side slope of the given cross-section shown: cross-sectional notes -2.6 4.63 6.67 -1.84…

A:

Q: e shape factor for the section as shown -3d 3d - fe 2d

A:

Q: Draw to show the subgrade working area.

A: Subgrade soil -  The integral part of the road pavement which provides adequate support to the…

Q: (D) -

A: A sectional view in engineering drawing is a representation of an object as if it were cut by an…

Q: Pls provide an isometric drawing for a gatehouse with an inclined roof and rectangular gateway…

A: Brief concept introduction- Isometric drawing- Isometric drawing is a type of three-dimensional…

Q: a) top most, lef tmost FIND: b) botton-most, right-most 3cm S.ם r= 1.25 y 125 } 05 Vb cm 1.5 3 I 1,5…

A:

Q: V5-4. For the 50-foot grid shown in Fig. 5-12, redraw, and sketch all one-foot contour lines. the…

A: Calculations of the distances of the points from the lower levels

Q: draw an isometric view of HEXAGONAL PRISM  where the base is 25mm and height 50mm.

A: Isometric view: It is also known as isometric projection. It is defined as the visual representation…

Q: Given the three orthogonal projections, identify the dihedral and draw the corresponding perspective…

A: Given data:- The three orthogonal projections are shown,

Q: Draw a detailed layout of a column formwork with dimensions.

A: The solution is in step 2:

Q: 70 27 52 18 27 14 34 OC

A: Handmade drawing are attached for better understanding.

Q: Define struts.

A: Struts:- They are long, slender structural members in an assembly which are subjected to the only…

Q: PART 1. AREA & VOLUME OF PRISMS Draw the indicated views for the isometric drawing below. Isometric…

A: An isometric view is given, we need to draw: 1. Top view 2. Left view 3. Front view

Q: Draw a sketch of  the section cross-section and the elevation view of this beam below

A: To draw:A sketch of  the section cross-section and the elevation view of this beam below

Q: Draw a detailed layout of a wooden wall form with dimensions.

A: Formwork are temporary mould used for casting different section of the structure like beam, column,…

Site Plan Requirements

A site plan (also known as a plot plan) is a diagram or process to show the proposed improvements on an existing property. A site plan is important, as it provides information regarding the landscape features of a given plot of land.  Zoning is done or can be understood with the help of a site plan.