Situation5. A line is recorded as 472.90 m. long. It is measured with a 0.65 kg. tape which is 30.005 m. long at 20°C under a 50 N pull supported at both ends. During measurement, the temperature is 5 °C and the tape is suspended under a 75 N pull. The line is measured on 3 % grade. Cross-sectional area of the tape is 3 mm^2.  a. Compute the actual length of tape during measurement.

Q: D. 445°

A:

Q: Problems: Analyze the rigid frame given below using either the Portal Method or the Cantilever…

A:

Q: 4. A Em tape weighs 0.0508 kg/m. During discipline measurements, the tape become subjected to a load…

A:

Q: Consider the cantilever beam shown in (Figure 1). Suppose that IAB = 600(106) mm²¹, IBC = 150(106)…

A: IAB = 600 × 106 mm4  IBC = 150 × 106 mm4  E = 200 GPa  Determine  a. Deflection at point-C.  b.…

Q: Determine the location (mm) of neutral axis from the effective compression concrete fiber under…

A: Width of beam, b = 450 mm Total depth of beam, D= 675mm Effective depth of beam, d= 675-75 = 600 mm…

Q: For the frame shown in Figure AN-17, using the Moment Distribution Method: NOTE: If I is not…

A:

Q: A 2 m long steel wire is fixed and hanging vertically with a tensile load of 2 kN and causes it to…

A: ##Determine the diameter ofthe steel wire ##

Q: 3. A horizontal circular plate weighing 100N is suspended as shown from three wires that are…

A:

Q: due to buckling must be considered. If E = 240GN/m? and L/r = 90 determine the boundary condition…

A:

Q: Solve the problem with complete solution in landscape orientation by placing it in a short coupon…

A: To find magnitude of friction force acting on each block

Q: A 100m steel tape is used to measure the distance of the line and found to be 1529.28m long. During…

A:

Q: Given: F |Change in length of CF=0.00208a mm Area(BE)=150a mm? E Area(CF)=150a mm? 18a mm E E=200…

A: When the load is acting on the body or specimen there is some deformation or change in the dimension…

Q: .A rectangular beam, which length from the compression fiber to the neutral axis is equal to 340 mm.…

A:

Q: The rigid pipe is supported by a pin at A and an A-36 guy wire BD. The wire has a diameter of 0.29…

A:

Q: A 30 m tape weighs 12 g/m and has a cross sectional area of 0.020 cm?. It measures correctly when…

A: Given data: L=30 m W=12 g/m  A=0.020 cm2 Standard pull=85 N Field pull=85 N Standard…

Q: A 30-m tape weighs 12.5 g/m and has a cross-section of 0.022 cm?. It measures correctly when…

A:

Q: O Figure Q2b shows a solid and homogeneous section, where (31.25 mm, 41.54 mm) are its centroid…

A:

Q: 100m tape weighs 0.0508 kg/m. During field measurements, the tape was subjected to a tension of 45…

A:

Q: 50 kN m A 4 m El = constant E =70 GPa I = 164 (10) mm tslduob lo anollida %3D %3D

A:

Q: Hello, can someone help me with this pls. Determine the vertical component of the force applied at…

A:

Q: Please show all work provided for the following problem so I can understand. Please show step by…

A: Step 1:

Q: What pull in kilogram (normal tension) is required in order that the effect of sag will be…

A: Surveying through tapes can be quiet erroneous. Several errors like error due to slope,…

Q: 1A 50 m tape weighs 2.5 kg. Ever y time measure ment is performed, the tape is supported points at…

A:

Q: (7) Let's practice moment of inertia calculations on this built-up cross-section. It is made of four…

A:

Q: -4 in 1 in Вох 2 Shear Flow: la A T-shaped beam is made by attaching two 1 × 4 in boards using nails…

A: To Find :- Shear Stress at Neutral Axis Shear Flow at the joint

Q: Calculate: 1. moment resistance 2. Minimum area of reinforcement 3. Maximum area of reinforcement…

A: Given;b = 150 mmD = 250 mmCover = 25 mmd = 250-25 = 225 mmNo. of Bar = 2dia. of Bar  = 16 mmFck = 25…

Q: 5. Four 1-in.-diameter pegs are attached to a board as shown. Two strings are passed around the pegs…

A:

Q: Determine maximum principal stress

A: To find maximum principal stress

Q: Neslyn used a 50m steel tape used to measure a certain distance. It was later found that the tape is…

A:

Q: Answer is letter B

A: Given data- Diameter(D) = 8in Height (H) = 16in Youngs modulus (E) = 2.5× 10^6 lb/in² Unit…

Q: A steel wire 29 ft long, hanging vertically, supports a load of 610 lb. Neglecting the weight of the…

A:

Q: Given the following: b=380mm d= 530mm fc'=30MPA fy=320MPA Mu=650KN-m Determine As A. USE NSCP 2015,…

A:

Q: H.W.1 A steel pipe that contains castor oil (p=1.8624 slug/ft³) is 6 ft in diameter. Determine the…

A:

Q: Three forces are acting on the eyebolt shown below. All forces intersect at a common point O.…

A: Given data in question  Forces 2500, 3000 & 4000 Angles 45, 25 & 30° To find out  Resultant…

Q: What is the horizontal displacement at Joint D in mm? I=15.5 x 10 mm and E= 200 GPa Seg Origin Limit…

A:

Q: the floor and at A 40 m bar weighing loo N is rerting ot points a srnooth on and against a smooth a…

A:

Q: DI01) D102) 150- 600 (NOTE: TT shows the continuity of the slab edge ) 1. Determine the design…

A: Consider the given data fck=30Mpa fy = 420Mpa  Beam = 300 x 600mm  Column = 300 x 500mm  Column…

Q: A uniform 25kg bar, 6.0m long is suspended by a cord shown. What is the tension in the cord? wall…

A: Given:-Weight of bar = 25 kg Lenge of bar=6 m

Traverse Survey

Traverse surveying is a popular method of surveying. Traversing is that type of survey where several connected survey lines form a framework and the directions and lengths of the survey lines are measured with the help of a tool to measure angles and tape or chain respectively. Traverse networks involve placing survey stations in a queue or trail and using pre-tested points as a basis for looking at the next point. This type of surveying is different from Tacheometric surveying, where only angles are measured and the process of chaining is reduced.