SITUATION. An 8-m long ladder weighing 900 N is shown in the figure. It is required to determine the horizontal force P that must be exerted at point C to prevent the ladder from sliding. The coefficient of friction between the ladder and the surface at A and B is 0.20. BN W = 900 N %3D 4m 4.59m 2 m 35° A, AN 6.55m Determine the required force P. B.

SITUATION. An 8-m long ladder weighing 900 N is shown in the figure. It is required to determine the horizontal force P that must be exerted at point C to prevent the ladder from sliding. The coefficient of friction between the ladder and the surface at A and B is 0.20. BN W = 900 N %3D 4m 4.59m 2 m 35° A, AN 6.55m Determine the required force P. B.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

how can a house be safe during earthquake source zone liquefaction hazard
The homogeneous disk of mass m is resting on the right-angled supporting surfaces shown. The tension P in the cord is very gradually increased from zero. If the friction at both A and B is characterized by us = 0.23, what happens first - does the homogeneous disk slip in place or does it begin to roll up the incline? Determine the value of P at which this first movement occurs. Assume 0 = 25° B 0.75r/ Answer: P = i P Ө mg
Problem 13.21 The 450-kg mine car is hoisted up the incline using the cable and motor M. For a short time, the force in the cable is F= (3000t2) N, where t is in seconds. (Figure 1) Figure 1 of 1 ₁ = 2 m/s wh T Part A If the car has an initial velocity ₁ = 2m/s at s = 0 and t = 0, determine the distance the plane when t = 3 s. Express your answer to three significant figures and include the appropriate units. S = O D Submit |μA Value Units My Answers Give Up ? Provide Feedback moves up Continue
Compute for the unknown Line AB BC CD DE EA LINE AB BC CD DE EA Distance 300 400 250 350 277.96 DISTANCE 250 UNKNOWN 300 UNKNOWN 400 Bearing S 37 30 E S 43 15 W N 73 W UNKNOWN UNKNOWN BEARING N 73 00 W N 12 45 E S 37 30 E N 65 45 E S 43 15 W ■
Use Slope-Deflection Method to solve for the moment reaction at C in kN-m on the 250 mm x 350 mm beam shown in the figure below. Assume E = 80 GPa and use a = 1.5 m, b = 2.3 m, c = 40 kN and d = 42 kN/m c kN d kN/m B, "b" m 3 m
The coefficient of static friction for both wedge surfaces is 0.34 and that between the 34-kg concrete block and the 25° incline is 0.66. Determine the minimum value of the force P required to begin moving the block up the incline. Neglect the weight of the wedge. P 3.7 Answer: P = 34 kg 25° N
2. The ladder has a uniform weight of 80 N and rests against the wall at B. If the coefficient of static friction at A and B is μs = 0.4, determine the smallest angle 0 at which the ladder will not slip. □□□□□:0=46.4° 15m
423 N is also wrong. Please answer correctlg
Note:hand written solution should be avoided.
How do you prefer a ‘tracked drive’ system than a ‘tired drive’ system for an excavator?
Problem 13.21 The 450-kg mine car is hoisted up the incline using the cable and motor M. For a short time, the force in the cable is F= (3000t2) N, where t is in seconds. (Figure 1) Figure 1 of 1 ₁ = 2 m/s wh T Part A If the car has an initial velocity ₁ = 2m/s at s = 0 and t = 0, determine the distance the plane when t = 3 s. Express your answer to three significant figures and include the appropriate units. S = O D Submit |μA Value Units My Answers Give Up ? Provide Feedback moves up Continue
determine the vertical reaction at B in kN using any Geometric Method. Consider 250 mm x 400 (b x h) mm section and E = 100,000 MPa. Enter the absolute value only and round-off your answer to 3 decimal places