The 450-kg mine car is hoisted up the incline using the cable and motor M. For a short time, the force in the cable is F= (3000t2) N, where t is in seconds. (Figure 1) Part A If the car has an initial velocity ₁ = 2m/s at s = 0 and t = 0, determine the distance the plane when t = 3 s Express your answer to three significant figures and include the appropriate units. 8 = Submit μA Value Units My Answers Give Up ? moves up

The 450-kg mine car is hoisted up the incline using the cable and motor M. For a short time, the force in the cable is F= (3000t2) N, where t is in seconds. (Figure 1) Part A If the car has an initial velocity ₁ = 2m/s at s = 0 and t = 0, determine the distance the plane when t = 3 s Express your answer to three significant figures and include the appropriate units. 8 = Submit μA Value Units My Answers Give Up ? moves up

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

please show complete solution. last 30 minutes left.. thank you!
Calculate the reaction Use 3 decimal places Base your calculation to the incomplete solution
If blocks A and B has the total mass of 250 grams with a ratio (A:B) of 2:3, what will be the smallest force F needed to cause motion of block B if P=300 N? Let the static friction of the surfaces between A & B and B & C will be 0.25 and the surfaces between the ropes and pegs D & E be 0.35.
Hi. Please solve this question and the complete solution. Thank you
Determine the tension in the rope and the acceleration of each block. Answer: 32.7 N, 8.175 m/s^2
2
A supporting rope is loaded with a line load q(x) = q0 between points A and B. The rope shall be stretched such that the slope of the rope at point A is zero. If l = 10 m and h = 2.3 m, determine the (a) horizontal tensile force and (b) the maximum force in the rope. q0 (kN/m) = 20.627
For theloading shown, use the double-integration method to determine (a) the equation of the elastic curvefor the cantilever beam, (b) the deflection at the free end, and (c) the slope at the free end. Assumethat Elis constant for the beam. Let w = 6 kN/m, L= 6.0m, E = 205 GPa, and I = 150x 10° mm“. Wo L Answer: (b) VA = -14.049 mm (c) ®A = 0.002809 rad
The hoisting arrangement for lifting a large pipe is shown in the figure SD-05Q002. The spreader is a steel tubular section with outer diameter 75 mm and inner diameter 60 mm. Its length is 2.5 m and its modulus of elasticity is 200 GPa. What is the maximum weight of pipe, in kN, that can be lifted based on the following conditions? (Assume pinned conditions at the ends of the spreader.) Use: V = 3 H = 4 Problem 7 Based upon a factor of safety of 2.0 with respect to Euler buckling of the spreader. a. 205 b. 434 c. 355 d. 217 Problem 8 Based upon the allowable stress design if Fy = 248 MPa. a. 205 b. 434 c. 355 d. 217 Problem 9 Based upon the critical stress. a. 205 b. 434 c. 355 d. 217
1
The 2.5-Mg car is being towed by a winch. If the winch exerts a force of T = 132.2(s + 1) N on the cable, where s is the displacement of the car in meters, determine the speed of the car in m/s when s = 11 m, starting from rest. Neglect rolling resistance of the car.
The hoisting system shown is used to easily raise kayaks for overhead storage. Determine the velocity and acceleration of the kayak (positive if upward, negative if downward) when y = 95 in. if the winch M reels in cable at the constant rate i = 8 in./sec. Assume that the kayak remains level. The distance b = 67 in. Answers: V = M a = i i ·b. ·b in./sec in./sec² B b