Situation - A square tubular section having an outside dimension of 450 mm and 16 mm thick as shown in the figure is used as a column to support a load of P. y 15. Calculate the radius of gyration (mm) of the column section.

Q: A solid 2.5 in. diameter cold-rolled brass [G=6,400 ksi] shaft that is L1+L3=123 in. long extends…

A: The given data is: Internal diameter=2.5 in External diamter=3.75 in Length of aluminum section…

Q: DETERMINE THE FORCE (Ib) FOR MEMBER AC GIVEN THE DATA BELOW: F1 = 830 lb F2 = 1,043 lb "Note: for…

A: Using method of joints the force in AC can be calculated.

Q: efore a load is applied, a rigid bar is fastened to two vertical rods. Calculate the vertical…

A:

Q: A steel block is axially loaded with ? = 10 ?? as shown in the figure with length equal to 3? and…

A: The load is P=10 kN. The length is l=3 m. The cross-sectional area is A=1000 mm2. The modulus of…

Q: (a) Based on the figure, give the minimum and the maximum of the external load, P. (b) Based on the…

A: Double D ring Below shows a Double D ring secured with a Nut and Bolt.

Q: Three solid cylindrical rods are welded together to form the compound axial member shown in the…

A: Load will be P in each road.

Q: A 13-m-long flat steel bar AB has a varying width as shown in the figure. Calculate the required…

A:

Q: A homogeneous steel beam is loaded from the figure below. The Cross- Sectional area of the beam and…

A:

Q: Q 2. For the symmetrical section in figure 2 shown below, calculate B mm 350 mm 0.8 B mm Figure (2)…

A: We have to determine the elastic section modulus and plastic section modulus and shape factor and…

Q: In (Figure 1), u 4 kN/m and wp7 kN/m. Replace the distributed loading by an equivalent resultant…

A:

Q: 1. The triangular block shown in Fig. P-010 is subjected to the loads P = 1600 lb and F = 600 lb. If…

A: Given data Force F = 600 lb Force P = 1600 lb Side AB = 8 in Side BC = 6 in To resolve Force in…

Q: Q2: A rigid bar is suspended from two wires of equal lengths 250 cm as shown below. Take E,= 210…

A: given data ,ES=210GPaEb=110GPalength =250cm1)  FB+FS=10000N=10KN    →(1)Now defoemation will be same…

Q: The 33-mm-diameter A992 steel rod is subjected to the loading shown. Take E= 200 GPa. (Figure 1)…

A:

Q: strain in the tension bars equal to  0.004 and  in the design process use 60% of this rho max.…

A: Given : DL = 10 kN/m LL = 8 kN/m UDL & 15 kN/m UVL 8 m length fc = 21 MPa and fy = 276 MPa

Q: Find the magnitude P of the largest additional vertical force that can be applied to the bar decimal…

A:

Q: Three solid cylindrical rods are welded together to form the compound axial member shown in the…

A: Given data: E=47 GPa uD=30 mm →

Q: The rigid AB beam shown in the figure is supported by elastic rods 1 and 2 at points A and B.…

A:

Q: An aluminum alloy [E = 70 GPa; V = 0.33; a = 23.0×10-6/ºC] pipe is subjected to a tensile load P.…

A: To Find :- magnitude of load P

Q: The column BC shown below has a solid cylindrical cross-section with a diameter of 30 r Determine if…

A: GIVEN DATA:-⇒d= 30mm⇒P= 30 KN⇒Sy= 350 MPa⇒E= 207 GPa

Q: The steel tie-bar shown in the figure has been designed to carry a tension force of 76 kN when…

A:

Q: Use Euler's formula to determine the critical load and critical stress for the column of height H…

A: Consider the diagram shown below. Both end are fixed. The height of the column is 4 m.

Q: The assembly shown in the figure consists of a brass core (diameter d₂ = 0.25 in.) surrounded by a…

A: Given values: Assembly of brass core surrounded by steel shell. Brass core diameter, Db = 0.25 in.…

Q: A SOLID ALUMINUM SHAFT 2 INCH DIAMETER IS SUBJECTED TO TwO TORQUES AS SHOWN IN THE FIGURE. DETERMINE…

A:

Q: As the pellet is about to be released, what is the total elongation (mm) of the rubber? O204 072 O…

A: Total Unstretched length of rubber ,  L = 60 mm a= 100 mm b = 40 mm TO determine : Total elongation…

Q: STATICS For the figure shown, if the resultant of the forces is acting at the slab center, O O 10…

A:

Q: DETERMINE THE FORCE (Ib) FOR MEMBER AC GIVEN THE DATA BELOW: F1 = 997 lb F2 = 1,449 lb **Note: for…

A:

Q: neter is 70 mm and the allowable shear strain is 0.02 rad imum permissible length of the bar will…

A:

Q: A. In the figure, a longitudinal hole is bored across the length of a cantilever beam having a…

A:

Q: etermine the force in each member of the truss. State e members are in tension or compression. Take…

A:

Q: (3) The cantilever shown in the figure is to be designed plastically with a load factor of 2. Length…

A:

Q: In the figure below, the 1300-kg uniform bar AB is suspended from two cables AC and BD each with a…

A:

Q: Determine the largest weight W that can be supported by the two wires shown in figure below. The…

A:

Q: 342 Strength of Materials 16. A steel post (E = 200 GPa) having thickness t = 3 mm and height L = 2…

A:

Q: Compute using Euler's formula: A square aluminum bar is to support a load of 65kN on a length of…

A:

Q: (4) As shown in the figure, the three steel plates are subjected to tensile force P, and seven…

A: When two plate is connected by single plate at middle and it is connected by means of rivet or bolt…

Q: QUESTION 3. A simply supported beam, having notches on its surface, is subjected to a triangular…

A: factor of safety F=1.5 varying loading zero at mid and w0 at ends ∑fy=0;    sum of support…

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.