SITUATION 4. AN OIL WITH SG = 0.86 FLOWS THROUGH A PIPE 30in. IN DIAMETER AT 700gpm 5. Determine the average velocity in m/sec. * Your answer 6. Determine the average flowrate in ft3/sec. * Your answer

SITUATION 4. AN OIL WITH SG = 0.86 FLOWS THROUGH A PIPE 30in. IN DIAMETER AT 700gpm 5. Determine the average velocity in m/sec. * Your answer 6. Determine the average flowrate in ft3/sec. * Your answer

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q1\ A ball made of INOX AISI 365 steel with density of 8.52 gr/cm3 was used to determine the viscosity of oil with specific gravity of 0.91. In the viscometer, the ball traveled 19 cm in 2.2 seconds. If the diameter of the ball is 2.95 mm, what is the viscosity of the oil in pa.s ? assume that water density is 1000 kg/m³.
Hello, can I get help please?
The velocity profile of a liquid flowing through the pipe is approximated by the truncated conical distribution as shown in (Figure 1). Suppose that V = 4 ft/s. Hint: The volume of a cone is V=1/r²h. 0.3 ft 0.6 ft 0.3 ft DE V Determine the average velocity of the flow. Express your answer to three significant figures and include the appropriate units.
Need answer only
Question 7 Which of the following is true about Friction Factor? Choose all that apply. Friction factor tends to be higher for turbulent flows. Friction factor old steel pipe > Friction factor new steel pipe (given the same diameter and fluid). Friction factor is used to determine minor losses. Friction factor for laminar flows is (64 / Re).
Develop the expression to determine: the elevation of the oil-water surface (Yi) and the pressure gradient for a water phase and an oil phase that is moving between two parallel plates showed on the figure. The flow rates at the inlet are 0.1 ft3/sec (same for both fluids) and the viscosities are 100 and 0.89 cps for oil and water respectively. 01 Water 12" 0il 2 Water 1 Fig. 1 Laminar Flow of Water and oil between interface Two Parallel Plates. Fig. 2 Two Dimensional Flow of oil and Water.
I need the answer to the question in fluid mechanics
The velocity profile of a liquid flowing through the pipe is approximated by the truncated conical distribution as shown in (Figure 1). Suppose that V = 4 ft/s. Hint: The volume of a cone is V= r²h. 0.3 ft 0.6 ft V 0.3 ft Determine the average velocity of the flow. Express your answer to three significant figures and include the appropriate units.
What is the velocity of the flow of water in leg B of the tee shown in the figure? A 4 m diameter V = 6 m/s 4 m/s с B 2 m diameter V = ?
The diagram below shows a pumping system to pump water to an elevated tank. The next page shows the performance curve of a specific type of centrifugal pump. The loss factors at the inlet and outlet are 0.5 and 1.5 respectively while the loss factor associated with the bend is 1.5. The diameter of the pipe is 0.050 m while the total pipe length is 400 m. In order to simplify the calculation you can assume that the friction factor is f= 0.036. Determine the duty point of this pumping system and thus determine the flow rate of the pump for an impeller diameter of 140 mm? Also determine the shaft power of the pump and give an estimate of the pumps efficiency at the duty point. Given that the pump is located 1.80 m above the water surface (1), and the pipe length from inlet to pump is 6.0 m, determine the NPSHA at the pump and state whether cavitation is likely to occur. Sol: 3.6 m 40 H m 30- P 10 20- K₁ = 0.5 5- kW 2- 1- 13 4 2- NPSH K₁ = 1.5 170 160 150 140. 130_ (1) Q 10 Pump 20 54…
8. Compute the probable density of a fluid inside a floating spherical balloon having a 2m diameterif the tension in the balloon’s tie rope is observed to be 2kgf. Assume that the density of air is1.18kg/m3. a. 0.7225kg/m3 b. 0.6225kg/m3 c. 0.7025kg/m3 d. 0.5848kg/m3
Pb-8a.