Situation 3: A W12x22 simply supported beam carries a uniformly distributed load. The properties of the section relevant to the problem are as follow: Use A50 steel and Cb - 1.14 d=312 mm bf 102 mm tf - 10.8 mm tw = 6.60 mm kdes 18.4 mm ry-21.5 mm Ix 64.5 x 10^6 mm^4 ly 1.94 x 10^6 mm^4 Sx416 x 10^3 mm^3 Zx 480 x 10^3 mm^3 J-122 x 10^3 mm^3 Cw44.0 x 10^9 mm^6 1. Which of the following nearly gives the Design Strength Moment (LRFD) if the span of the beam is 2.5m? 89 KN-m O 114 KN-m 123 KN-m O 101 KN-m

Situation 3: A W12x22 simply supported beam carries a uniformly distributed load. The properties of the section relevant to the problem are as follow: Use A50 steel and Cb - 1.14 d=312 mm bf 102 mm tf - 10.8 mm tw = 6.60 mm kdes 18.4 mm ry-21.5 mm Ix 64.5 x 10^6 mm^4 ly 1.94 x 10^6 mm^4 Sx416 x 10^3 mm^3 Zx 480 x 10^3 mm^3 J-122 x 10^3 mm^3 Cw44.0 x 10^9 mm^6 1. Which of the following nearly gives the Design Strength Moment (LRFD) if the span of the beam is 2.5m? 89 KN-m O 114 KN-m 123 KN-m O 101 KN-m

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 2.10 A square yellow it is subjected t the allowable t mum allowable cross section if

Q: Determine the ASD design strength for the A36 plates shown. Use Fy = 248MPA and Fu = 400MPA.

A: Solution: Given data: Fy=248 MPaFu=400 MPa

Q: compound steel (E = 30,000 ksi) bar is subjected to the loads shown. Bar (1) has a cross-sectional…

Q: A beam is fabricated by connecting two steel plates to two C250 x 37 rolled-steel channel sections…

A: Given data:- Rolled steel channel section C250×37 Width of steel plate, b = 355 mm Thickness of…

Q: uation 6: A W18x97 simply supported beam carries a uniformly distributed load. The prope ction…

A: 998 kNm

Q: A compound steel (E = 30,000 ksi) bar is subjected to the loads shown. Bar (1) has a cross-sectional…

Q: Determining the spacing of a pair of connecting screws (connectors) between the slab and the steel…

Q: Problem 4: Use A992 steel and select a W shape. The service dead load is 142 kips, and the service…

A: First we summarise the given data : Service dead load = 142 kips Service live load = 356 kips To…

Q: A compression member with an effective length of KL = 12 ft is built up from a W shape and a…

Q: W 10x45 is connected to two plates with two lines of ¾” bolts as shown below. Determine the tensile…

Q: A compound steel (E = 30,000 ksi) bar is subjected to the loads shown. Bar (1) has a cross-sectional…

Q: A compound steel (E = 30,000 ksi) bar is subjected to the loads shown. Bar (1) has a…

Q: Find: Calculate the following: Figure a. The gross moment of inertia, Ig b. The location of the…

A: Moment of Inertia:The moment of inertia is defined as the amount indicated by the object opposing…

Q: 3. Determine the nominal compressive strength of a W360 x 44 of A992Gr50 steel column having length…

A: Given, L = 4m or 4000 mm Fy = 345 MPa

Q: Please show all work provided for the following problem so I can understand. Please show step by…

A: See image below for the explanation

Q: A steel rod of 30 mm diameter is used as a tie member in roof truss. It may be subjected to reversal…

A: Given-

Q: Per missible As in section to ensure tensile Compute the design strength of beam shown if fy = 420…

A: To find : design strength

Question

Situation 3: A W12x22 simply supported beam carries a uniformly distributed load. The properties of the section relevant to the problem are as follow: Use A50 steel and Cb -
1.14
d=312 mm
bf - 102 mm
tf 10.8 mm
tw = 6.60 mm
kdes 18.4 mm
ry-21.5 mm
Ix- 64.5 x 10^6 mm^4
ly- 1.94 x 10^6 mm^4
Sx416 x 10^3 mm^3
Zx 480 x 10^3 mm^3
J-122 x 10^3 mm^3
Cw-44.0 x 10^9 mm^6
1. Which of the following nearly gives the Design Strength Moment (LRFD) if the span of the beam is 2.5m?
89 KN-m
O 114 KN-m
O 123 KN-m
O 101 KN-m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A steel plate (called a cover plate) having cross-sectional dimensions W2 5.0 in. x 0.4 in. is welded along the full length of the bottom flange of a W, 12.0 in. x 87.0 in. wide-flange beam (see the figure, which shows the beam cross section). I W2 cover plate What is the percent increase in the smaller section modulus (as compared to the wide-flange beam alone)? Round your answer to two decimal places. % in smaller section modulus =
Use A992 steel and select a W shape using LRFD. D = 350 k L = 1000 k 35' Strong axis T 10' Figure 4 15' 10' www SHOW ****** Weak axis
P,= 500 k J. P, = 1,000 k I P,= 500 k Py=1,000 k fixed fixed Check whether a 17 ft W 14 x 211 section of A992 steel can safely carry the given applied service loads pinned 35 ft 18 ft pinned pinned Strong Axis Weak Axis
Height h=584.6 mm Flange thickness t = 11.4 mm Flange width b = 213.2 mm T What is the shear resistance of a universal beam (UB) with the following dimensions [EC3 Section 6.2 Resistance of cross sections]: Cross sectional area A = 105 cm² Web thickness tw = 7.8 mm C y-.-.-.-.-.-y Root radius r = 12.7 mm Yield strength fy = 355 N/mm² Calculate the shear resistance and give your answer to the nearest whole kN. Do not include units in your answer.
A compound steel (E = 30,000 ksi) bar is subjected to the loads shown. Bar (1) has a cross-sectional area of A₁ = 0.30 in.² and a length of L₁= 115 in. Bar (2) has an area of A2 = 0.30 in.² and a length of L₂ = 130 in. Bar (3) has an area of A3 = 0.20 in.2 and a length of L3=45 in. The loads and angles are P = 22 kips, a = 38°, Q = 15 kips, ß = 61°, and R = 10 kips. Determine the vertical deflection of end A. A downwards deflection is positive, while an upwards deflection is negative. D (1) L₁ (2) B Tox A -U R 24°C Cloudy (3) Q L2 L3
The given angle bar L125x75x12mm with Ag = 2,269 sq.mm. is connected to a gusset plate using 20 mm diameter bolts as shown in the figure. Using A36 steel with Fy = 248 MPa and Fu = 400 MPa, determine the following: a. ultimate tensile strength (kN) based on tensile rupture
A steel plate (called a cover plate) having cross-sectional dimensions W2 8.0 in. x 0.7 in. is welded along the full length of the bottom flange of a W, 12.0 in. x 14.0 in. wide-flange beam (see the figure, which shows the beam cross section). I W2 cover plate What is the percent increase in the smaller section modulus (as compared to the wide-flange beam alone)? Round your answer to two decimal places. % in smaller section modulus =|
For the built-up shape shown, determine:A) the elastic section modulus and the yield moment (b) the plastic section modulus and the plastic moment Mp.Bending is about the x-axis, and the steel is A572 Grade 50. Fy = 345 MPa
Given the truss shown, solve the following. Use A36 steel and assume there are two lines of three 19 mm bolts in each flange. Hole diameter is assumed to be three mm more than the bolt diameter. Neglect the weight of the section. a.What is the capacity of member CG? b. Design member CG using a W section. c. What is the tensile capacity of the section for CG based on gross area? The following W Section were considered for the design: W10x33 W14x38 W8x40 W16x36 W10x39 W8x13 189 KN 1.50 HL B 145 KN 1.50 E + 137 KN 121 KN -3.00 + 12.00 3.00 154 KN + W4x13 W6x9 W10x12 200 KN -1.50 1.50 1 030 T 1.20 +2.40 0.60 L i 0.30
A compound steel (E = 30,000 ksi) bar is subjected to the loads shown. Bar (1) has a cross-sectional area of A1 = 0.35 in.2 and a length of L1 = 120 in. Bar (2) has an area of A2 = 0.35 in.2 and a length of L2 = 90 in. Bar (3) has an area of A3 = 0.20 in.2 and a length of L3 = 45 in. The loads and angles are P = 29 kips, α = 32°, Q = 11 kips, β = 57°, and R = 14 kips. Determine the vertical deflection of end A. A downwards deflection is positive, while an upwards deflection is negative.
How to solve this question step by step
A W12x79 of A573 Grade 60 (Fy = 415 MPa) steel is used as a compression member. It is 8 m long, pinned at the top fixed at bottom with additional lateral support at mid height in the weak direction. The properties are as follows: Ag = 14,500 sq.mm, Ix= 258.6 x10^6 mm ^4 Iy=84.375 x 10^6 mm^4. 55. calculate the critical slenderness ratio with buckling about strong axis.