Situation 2: A rectangular beam has the following properties. Assume 12 mm stirrups. Assume a single layer of reinforcements. Calculate Mu. Given: Width of the beam, 450 Over-all depth, h = 600 Tension reinforcements = 10 Comp reinforcements = 4 Specified strength of concrete, f'c 28 Steel yield strength, fy = 415 Note: Round off your final answer in 3 decimal places. No need to type the units.

Situation 2: A rectangular beam has the following properties. Assume 12 mm stirrups. Assume a single layer of reinforcements. Calculate Mu. Given: Width of the beam, 450 Over-all depth, h = 600 Tension reinforcements = 10 Comp reinforcements = 4 Specified strength of concrete, f'c 28 Steel yield strength, fy = 415 Note: Round off your final answer in 3 decimal places. No need to type the units.

Fundamentals Of Construction Estimating

4th Edition

ISBN:9781337399395

Author:Pratt, David J.

Publisher:Pratt, David J.

Chapter5: Measuring Concrete Work

Section: Chapter Questions

Problem 6RQ

See similar textbooks

Similar questions

Given fc' = 35 MPa, solve for the modulus of elasticity of concrete 27,800.00 MPa 27,805.57 MP O 200,000.00 MPa None of the above O O O O
Sub: Advance Reinforced Concrete design. Follow the ACI 318 design code for the design. Answer the question with all details. provide the drawings with all details. Don't Copy Paste from Other Solutions please. i will Upvote You Value Óf X1= 27.65 Value Of X2= 395 1- Design the beam BC of the frame shown in Figure 1 for bending moment and shear force according to ACI 318 code requirements. The concrete cover is 30 mm. Dead load and live loads are given in Figure 1. Provide all drawings in detail. Please do check for maximum and minimum flexural requirements, maximum and minimum spacing of the shear reinforcement. f=X1 MPa, fy=X2 MPa D.L.=5 ton/m L.L.= 3 ton/m 6 m 3 m
The three parts of this problem refer to the floor plan shown in the figure. Assume that the entire floor system isconstructed sand normal weight concrete that has compressive strength, fc= 4000psi. Also assume that thelongitudinal steel has a yield strength, fy=40 ksi, and that the transverse steel has a yield strength off yt= 40ksi. The slab thickness is 6”, with a superimposed dead load of 18 psf and live load of 26 psf.a).Design the spandrel beam between columns B1 and C1 for bending, shear, and torsion. Check that all of theappropriate ACI Code requirements for strength, minimum-reinforcement area, and reinforcement spacing are satisfied.b): Design the spandrel beam between columns A1 and A2 for bending, shear, and torsion. Check that all of theappropriate ACI Code requirements for strength, minimum-reinforcement area, and reinforcement spacing are satisfied.c). Design the spandrel beam between columns B2 and C2 for bending, shear, development length, andsplicing. Check that all…
Estimate concrete volume required for the concrete column
Figure C a 1 of 1 Part A Locate the centroid y of the composite area. Set a = 8 mm, b = 28 mm, d = 21 mm h = 44 mm. (Figure 1) Express your answer with the appropriate units. IU II Submit Part B IT' μÅ = Value Request Answer Determine the moment of inertia of this area about the centroidal x' axis. Express your answer with the appropriate units. μÅ Units Value ? Units ? "
Refer to the figure shown. 1450 300 Given are the following: fc' 35 MPa fpu = 1,500 MPa Aps 1,800 mm2 fpy 1,320 MPa Use bonded tendons as prestressed reinforcement. Determine the value of fos. (MPa) 650 120
= ======= == Q2- The architectural engineer proposed a width of 350 mm and a height of 750 mm for a cantilever beam shown below, as you a design engineer ,design this beam according to ACI-14 requirements and assume in your solution that: Mu 1300 kN.m fc 21 MPa and fy 420 MPa Bar diameter of 32mm for longitudinal reinforcement. Bar diameter of 12 mm for stirrups. Two layers of reinforcement for both tension and compression zone. ⚫Use bundle bars when it is possible. 350mm
Bonus
A symmetrical cross-section of a reinforced concrete shown has a value of f'c = 26.27 MPa and fy = 414 MPa. Calculate the nominal capacity based on the maximum steel area for a tension- controlled condition. Use the following dimensions: b = 498 mm d = 709 mm t = 152 mm web thickness - 152 mm b 1 I d
Show complete solution. Answer Choices: 2pcs 3pcs 4pcs 5pcs
Read the question carefully and give me right solution according to the question. Don't copy from other websites solution
(Use phi=0.90, NSCP 1992) a reinforced concrete beam has the following properties: beam width is 320 mm, effective depth is 640 mm, concrete strength is 25 MPa, reinforcing steel strength is 400 MPa and reinforcing steel modulus is 200 GPa. If the beam is to be designed for a balanced condition, find the required area of steel reinforcement in mm^2?