Figure Q1 shows a cross section for a reinforced concrete beam. The characteristic strengths of the concrete and steel reinforcement are 30 N/mm² and 500 N/mm², respectively. (i) Determine ultimate moment of resistance of the beam. (ii) If the beam is simply supported over a 6 m length and subjected to a concentrated load at the mid-span. Calculate the maximum concentrated load based on the moment capacity in Q1(b)(i). Ignore the self-weight.

Q: The picture of the graph isn't showing can you please resubmit it?

A: GIVEN: To Calculate: Draw the Graph of GRAIN size distribution curve.

Q: Write down the important steps for improving listening skills and vocabulary building

A: 1. Always look at the speaker and maintain eye contact. 2. Use positive body language. 3. Observe…

Q: Evaluate and find all the requirements with proper, neat, and readable handwriting solutions. Box…

A:

Q: I did not pay the subscription amount in order for my questions to be rejected!!! Please I need…

A: Solution: Given: Column Span = 3.3 m fck = 30.5 MPa fy = 472 MPa DL = 3.55 kPa LL = 4.55 kPa

Q: One of the following choices is not among the types of volume counts : * Time variation counts.…

A: Volume count  Counting the number of vehicles passing through a point in a given interval of time ,…

Q: In the area of Occupational Safety and Health (USH), rišk managemeht defined as a procedure to…

A: Solution: i) 1. Hazard is basically the potential for physical and mental harm. 2. Hazard can also…

Q: Write the name of thermal injuries? Write down the name of the two key words in Occupational Health…

A: in this question four question is asked from occupational health and hazard

Q: Note: Replace all zero digits of your ID number by number "2" Problem #4: Use X = Last 3 digits of…

A:

Q: Note: Replace all zero digits of your ID number by number "2" Problem #1: XN Use X Last 3 digits of…

A:

Q: Which of the following answers represent the appropriate label for arrow A indicated on the diagram…

A: The label A represents ACTUAL SCHEDULE.  Hence, the correct option is B.

Q: Answer the following service Engineering question. ( add reference and intext citation) Outline the…

A: Approach to solving the question: Kindly read with comprehension and I hope it helps :) Detailed…

Q: What are the main objectives of any Water Supply System

A: We need to explain the main objectives of any Water Supply System.

Q: Problem #4: Note: Replace all zero digits of your ID number by number "2" A B P. Use X = Last 3…

A:

Q: How exactly does one use a report generator, and what precisely is meant by a mock-up report?

A: Using a valid, reliable report generator ensures a clean and consistent availability of information…

Q: Please

A:

Q: Please answer it again in neat and good handwriting. the current handwriting is not at all clear.

A:

Q: 1. Determine the Degree of Freedom of the following Structure 25 KN 15 KN/m 2km F. - 3 m- -15 ft…

A: Given data in question  Structures  To find out  Degree of kinematic indeterminacy    Dk= degree of…

Q: How to draw a free body diagram please.

A: As per guidelines we need to answer only first question so please repost rest questions separately

Q: What are the best methods for data cleaning

A: This question is related to the Computer aided and design (Auto cad) from civil engineering.

Q: What is flow rate formula

A: there are different formulas for flow rate. that depends on situation.

Q: a) Explain fire hydrant system. (b) Give an overview of fire safety, risk and control.

A: The Fire Hydrant Protection System is an active fire safety device that is made to combat fires of…

Q: Determine the force in member DE of the truss shown. State if the members are in tension or…

A:

Q: What is the measurement benchmark（more than one answer） (multiple choice questions) A. position…

A: Measurement bench mark is a position reference and an elevation datum. It is a point with respect to…

Q: In technical writing, before collecting the relevant information of a report you should: a. Develop…

A: Technical writing is an important part it an important of future decision Therefore option (d) is…

Q: For the cross-section shown below, the centroid value from the top surface in inches is: * 0.5 in.-3…

A:

Q: X Oxidation process can happen between metal and organic solvent. False True ||| O العربية…

A: Oxidation is a process of removal of organic matter in the presence of oxygen. Oxygen also make…

Q: The state of a plane strain at a point has the components ɛ, = -300 (10). ɛy = -400 (106) and Yry =…

A: It is required to determine the normal strain in x direction.…

Q: Define the Pollution prevention and environmental regulation.

A: Pollution prevention Pollution prevention is the process of reducing or eliminating the production…

Q: Do not include the unit in writing the answer. Use small letters (lowercase) in writing the words…

A: Calculate area as follows:

Q: Please give proctor test results and graph.

A: Proctor test  A geotechnical laboratory test process known as the Proctor compaction test is used to…

Q: Assume that you are a hotel receptionist, and you ask each of the following to fill out a guest…

A: 1. A hotel receptionist is an employee who works at the front desk of a hotel or lodging…

Q: (a) What are human values in engineering ethics? (b) Define “Risk” in professional ethics…

A: Basic human values are termed  to those values which are present at the core of being human. The…

Q: 1) Define active fire protection system and its importance in a building.

A: Objective: To define active fire protection system and state its importance in a building.…

Q: The left and right water edges of a river are 3.75m and 65.25m, respectively, from an initial…

A: Area Velocity Method- This method is used to measure discharge in the river. It is generally…

Design criteria for structural loading

The different loads such as loads due to self-weight (dead load) and external loads such as live load, wind loads, seismic load, snow load, and other loads and load combinations that influence the design of a building are called structural loading. The nature of the applied load differs from changes in the location, design, and type of materials used. The design criteria require that structures must be designed and constructed to be able to withstand all load types that are expected to act upon the structure and render its usage for the designated purpose. The structural members such as beams, slabs, columns, and foundations help the structure to withstand the applied load. There are different institutes such as ASCE and ACI that provide building design codes to assure minimum safety requirements and quality of the structures.