Situation 2-A 12 m long simply supported beam will be subjected to a uniform moving load of 9 kN/m. It is desired to compute the maximum shear at point C which is 8 m from the left support. 19. Which of the following gives the ordinate of the influence line 5 m from the left support? A. 0.333 012-04 C. 0.583 D. 0.417 B. 0.500 20. What is the maximum negative shear at C in kN? A. 20 C. 22 B. 18 D. 24 21. What is the maximum positive shear at C in kN?HW A. 6 C. 10 B. 8 D. 12

Situation 2-A 12 m long simply supported beam will be subjected to a uniform moving load of 9 kN/m. It is desired to compute the maximum shear at point C which is 8 m from the left support. 19. Which of the following gives the ordinate of the influence line 5 m from the left support? A. 0.333 012-04 C. 0.583 D. 0.417 B. 0.500 20. What is the maximum negative shear at C in kN? A. 20 C. 22 B. 18 D. 24 21. What is the maximum positive shear at C in kN?HW A. 6 C. 10 B. 8 D. 12

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

7.85 The beam will fail when the maximum moment is Mmax = 30 kip⋅ft or the maximum shear is Vmax = 18 ki . Determine the largest intensity w of the distributed load the beam will support. Determine the largest intensity w.
Situation 5 - A steel drive shaft is 1.80 m long and its outer and inner diameters are respectively equal to 56 mm and 42 mm. The shaft transmits 180 kW while rotating 1t 1800 rpm. Use G = 77 GPa. 36. What is the applied torque in N-m? А. 1008 В. 849 37. Compute the maximum shearing stress in MPa. А. 40.5 В. 42.8 38. Compute the angle of twist in degrees. A. 1.72 В. 1.94 C. 637 D. 955 C. 27.1 D. 36.1 C. 2.05 D. 1.29
Five forces are acting on the cantilever beam AB. Find the resultant or a couple acting on the cantilever beam. 1400 N 800 N: 900 N 1000 N 500. N B 1.2 m 0.6m 0,9 m 1.5m. 0.6m
Determine the values of the shear V and the moment M at the following locations: (A) immediately to the left of D immediately to the right of D immediately to the right of F (B) (C) A 6 kN 2 m 12 kN-m ID 18 kN E F 2m 2m 2 m 10 kN -m 3 m B 12 kN
3. Determine the moment of the force F about point P. P A 360 mm 500 mm X x 2 m -3 m O 3 m 2 m 4. The magnitude of the force P is 250 N. Determine the moments of P about point O. A P 600 mm x 1 m Y F = {2i+ 4j6k) kN 3 m y
Lecture 2 A triangular roof frame consists of a horizontal tie rod and two rafters at inclined at 300 and 60⁰ respectively to the horizontal and is supported at the ends. It carries a load of 4 KN at the apex, determine the resulting thrusts in the rafters, the tension in the tie rod and the reaction at the supports. Using Lami's theorem N j at 30/ K X 4 KN raf 60
Problem 6 A force system is shown below. 50 N 90 N 40° 40 N-m 0.40 m 0.80 m 100 N a. Determine the magnitude of the resultant? b. Determine the angle that the resultant force makes with the x-axis? c. Determine the magnitude of the resultant moment acting at point O? :::::: W 090 0.30 m 0.50 m
Solve the following. Force P acting at an angle of 45° from the x-axis, along xy plane, prevents the pole AB, weighing 375N from falling. The pole leans against a frictionless wall at A. A 4m I 3.15m i.What is the value of force P, N? a. 116.80 c. 292.4 b. 197.40 d. 82.60 ii.Determine the reaction at A, Newtons a. 292.40 c. 116.8 b. 197.40 d. 82.60 iii. Compute the reaction at B along x, N a. 292.40 c. 116.80 b. 197.40 d. 82.60 iv. Compute the reaction of B along y, N a. 197.40 c. 82.60 b. 292.40 d. 116.80 v. Compute the reaction of B along z, N a. 82.60 c. 197.40 b. 116.80 d. 292.40 3.15m
Determine the mnaximum positive moment at C using the influence line and considering the given loads below. 20KN ISNn A Sm
A cantilever beam has a span of 2 m. and having a flexural rigidity of 40000 kN.m². At the free end of the beam there is a spring with a clearance of 200 mm below the beam. Spring constant is 252 N/m. #13 0.20 m #14 Find the force acting on the spring after a concentrated load of 800 kN is applied at the force end. #15 Compute the moment at the fixed end. Compute the deflection of the spring after a concentrated load of 800 KN is applied at the free end of the beam. P=800 KN
The figure below shows the reinforced concrete beam AB of a tourist lookout at the free end. Its weight per unit length is 2500N/m, and the beam rests on two pillars at A and B, with no fixed connection. A. Assuming the beam is uniform, which of the following gives the absolute maximum shear? i. 12500N ii. 10000N iii. 7500N iv. 22500N B. What is the value of the absolute maximum moment? i. 31250Nm ii. 20000Nm iii. 11250Nm iv. 22500Nm
The force F = 254 N acts from D towards E, as shown. 165 mm 330 mm 132 mm Determine the magnitudes of the moments of force F in N- m about the following lines. (a) OA N.m (b) ос N. m (c) CG N.m (d) GE N- m (e) GB N-m (f) AF N. m (g) GF N- m