A simply supported beam is subjected to a moving concentrated load of 23 kN. a. Calculate the maximum & minimum moment in the beam if the length is 8m. b. Calculate the maximum and minimum shear in the beam if the length is 8m. A simply supported beam of length L is load with a moving load concentrated P passing across the span of the beam. a. Determine the location of P from the left support that will cause maximum moment in the beam. b. Determine the maximum shear force that will carried by the beam

Q: UDL a-4 m, b- 6 m F-6 KN, UDL-15KN/m For the beam with loads as shown, draw the shear force diagram…

A:

Q: analysis the below feame. then draw the axial shear and moment diagram for the frame.

A: Degree of Static indeterminacy, Ds  Ds = number of unknown forces - number of equilibrium equations…

Q: Draw the influence lines for members DI and IJ of the truss depicted in the figure below assuming…

A:

Q: Determine the magnitude of the maximum shear in the beam. Answer in kN rounded-off to 3 decimal…

A: Given Data Find the maximum shear force and maximum bending moment diagram.

Q: O kN are placed on the floor beams. If the beams also sup ad of 700 Nm, determine (a) the maximum…

A:

Q: other end is held with a sliding support. Of beam its cross section is given below. To the beam, as…

A:

Q: the beam in the figure below is to be loaded with 20kN single axle load, a uniformly distributed…

A:

Q: Consider pin A, which is used in a single shear connection. Use the ultimate shear strength, the…

A:

Q: The simple bridge girder and series of concentrated load are shown in figures below. Simple beam: A…

A:

Q: For the truss shown in the figure below, assume that the loads are being transmitted to the bottom…

A: Solution  ILD for member DI  Pass a section through member DI as shown below When the Unit load is…

Q: #4 The beam is used to support a dead load of W k/ft, a live load of 2 k/ft and a concentrated live…

A: Calculation of Maximum  Reaction at A , BM at C , SF at right of A   due to given set of Loading  on…

Q: Analyze the statically determinate planer force system to calculate the reactions at the supports.…

A:

Q: Analyze the beam below: 1 m Α.Δ. 400 kN/m 6 m 2 m 600 kN B 2 m (a) determine the maximum moment…

A:

Q: The beam shown in figure carries a triangular load which varies from 20 kN/m at A to 0 kN/m at B and…

A: Given:Required:Reaction at BLocation of zero shear from AMaximum momentMoment at point B

Q: What is the maximum positive moment for the beam shown? Use the method of consistent deformations.…

A:

Q: M. A B E Hinge /C D L2 4 m 6 m

A:

Q: d live load of P kN. Determine (a) the maximum positive (upward) reaction at B, (b) the maximum…

A: For the above beam, Assume W1=87N/mW2=4kN/mP=3kN

Q: the beam shown, determine the maximum negative ent. In kN.m 19 kN 3 kN/m |B 2 m 2 m 2 m

A:

Q: Analyze the beam loaded and supported as shown: Ans.: A 40 kN Ans: 2 m 6m B Hinge (a) Determine the…

A: Given: Required: Maximum shear and bending moment

Q: Please answer part a b c

A: We will consider the UDL all over the beam. and draw ILD and take area under ILD.

Q: A conical vessel has a height of 24 cm. and a base diameter of 12 cm. It holds water to a depth of…

A:

Q: For the beam shown, determine the reactions at A, B and D. At B, C and D is a pin and at A is a…

A:

Q: The compound beam is pin supported at C and supported by a roller at A and B. There is a hinge (pin)…

A:

Q: UDL B C Fato F

A: support reaction: ∑MB=0RA×6+4×12×6-10×12=0RA=-28 KN∑FY=0RA+RB-4×12+10=0-28+RB-4×12+10=0RB=66 KN

Q: A unit load will pass in the simple beam shown. 1) The absolute reaction @ A and C when the unit…

A:

Q: For the simply supported beam shown, draw influence lines for moment at C (12-ft from support A),…

A: when the unit load at A and B then bending moment at C equal to 0 .and if the unit load at C then…

Q: PROBLEM 2 For the beam shown, determine the reactions at A, B and D. At B, C and D is a pin and at A…

A: To find support reaction at A,B,,D

Q: Problem 2: For the beam shown in Figure A. Find the reaction at support B (RB) B. Find the reaction…

A: Given data that,

Q: A bridge truss and a system of moving concentrated load are shown below. The bridge truss: A The…

A: Given: Point loads: P1=25 kNP2=30 kNP3=30 kNP4=50kN To find: ILD for member BC and calculate the…

Q: A cantilever beam has a span of 2 m. and having a flexural rigidity of 40000 kN.m². At the free end…

A:

Q: 2. Draw the influence line for (a) the vertical reaction at A, (b) the shear at C, (c) the moment at…

A: Since the given question has multiple sub parts therefore as per guide lines only 1-3 sub parts will…

Q: A beam is subjected to the loading condition shown below. Draw the influence lines for: a) the…

A:

Q: 25 kN/m A B -8 m- -8 m- E = 70 GPa I= 1,300 (106) mm² (Assume 50mm settlement @ Support B) C

A: Given data  E = 70 GPA = 70 × 103 N/mm2 I = 13 × 108 mm4  ∆B = 50 mm = 0.05 m

Q: What is the location of the absolute maximum shear from the left end of the beam? (in m) e. What is…

A:

Q: Question 2: For the beam shown below determine the maximum negative moment at point c if the dead…

A:

Q: For the truss shown in the figure below, assume that the loads are being transmitted to the bottom…

A: A truss with hinged support at G and roller support at C is given. To this, a train of load moves…