A cantilever beam has a span of 2 m. and having a flexural rigidity of 40000 kN.m². At the free end of the beam there is a spring with a clearance of 200 mm below the beam. Spring constant is 252 N/m. #13 0.20 m #14 Find the force acting on the spring after a concentrated load of 800 KN is applied at the force end. #15 Compute the moment at the fixed end. Compute the deflection of the spring after a concentrated load of 800 KN is applied at the free end of the beam. P=800 KN

A cantilever beam has a span of 2 m. and having a flexural rigidity of 40000 kN.m². At the free end of the beam there is a spring with a clearance of 200 mm below the beam. Spring constant is 252 N/m. #13 0.20 m #14 Find the force acting on the spring after a concentrated load of 800 KN is applied at the force end. #15 Compute the moment at the fixed end. Compute the deflection of the spring after a concentrated load of 800 KN is applied at the free end of the beam. P=800 KN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A beam has a width of 300 mm and has an effective depth of 400 mm and has a modular ratio of 9. It is reinforced by 4–28 mm diameter bars. Use WSD: f'c = 20.7 Mpa ; fy = 275 Mpa a. Find the location of the neutral axis measure from the top of the beam. b. Compute for the moment capacity of the beam considering compression alone. c. Compute for the moment capacity of the beam considering pension alone.
Replace the distributed loading by an equivalent resultant force and couple moment acting at point A.
The beam AB has a negligible mass and thickness and is subjected to a triangular distributed loading. It is supported at one end by a pin and at the other end by a post having a mass of 50 kg and negligible thickness. Determine the minimum force P needed to move the post. The coefficients of static friction at B and C are μB = 0.4 and μC = 0.2, respectively.
The cantilever beam carries a combination of a uniformly distributed load and a trapezoidal loading as shown. Determine the maximumn moment in kN-m. Given: wi = 3 kN/m, w2 = 8 kN/m, a = 3 m, and b = 6 m. Neglect the mass of the beam. w2 kN/m w1 kN/m A BI am b m
The beam AB has a negligible mass and thickness and is subjected to a triangular distributed loading. It is supported at one end by a pin and at the other end by a post having a mass of 50 kg and negligible thickness. Determine the two coefficients of static friction at B and at C so thatwhen the magnitude of the applied force is increased to P = 150 N, the post slips at both B and C simultaneously.
The cantilever beam carries a combination of a uniformly distributed load and a trapezoidal loading as shown. Determine the maximum moment in kN-m. Given: w1 = 5 kN/m, w2 = 6 kN/m, a = 2 m, and b = 4 m. Neglect the mass of the beam. w2 kN/m w1 kN/m B|I am bm A.
The horizontal force F acts on the handle of the wrench (i.e Fis parallel to xy-plane). What is x-component of the moment of this force about the origin "O"? F = 19.5 N, a = 36 mm, b = 200 mm, c = 10 mm, 0 30°. of B
Lecture 2 A triangular roof frame consists of a horizontal tie rod and two rafters at inclined at 300 and 60⁰ respectively to the horizontal and is supported at the ends. It carries a load of 4 KN at the apex, determine the resulting thrusts in the rafters, the tension in the tie rod and the reaction at the supports. Using Lami's theorem N j at 30/ K X 4 KN raf 60
A snow load of 3 kPa rests on a roof whose trusses are spaced 3m on center. Find: 1. Determine the magnitude of the equivalent concentrated load acting at point C.2. Determine the force at member BF. Specify if tension or compression.3. Determine the reaction at E
The cantilever beam carries a combination of a uniformly distributed load and a trapezoidal loading as shown. Determine the maximum moment in kN-m. Given: w- 5 kN/m, W2 = 6 kN/m, a = 2 m, andb- 5 m. Neglect the mass of the beam. w2 kN/m w1 kN/m AAAAAAAA b m am A.
Part I. Principle of Superposition. For the beam loaded as shown, it is required to determine the distribution of internal forces and moments on the beam. El is constant. The supports at B and C are rollers and D is pinned. 10 kN 3 kN/m 3 kN/m В A 3m 3m D 3m 4 kN 1. Determine the degree of indeterminacy of this beam. 2. Solve for all the support reactions. 3. Draw the shear and bending moment diagram for the beam.
1. The truck is moving along a 15 m span of beam. The front axle is 16 kN, the middle is 36 kN and the rear is 26 kN. The middle load is space 3m from the front and 6 m from the rear. a. Determine the moment under each axle. b. Calculate the maximum moment produced by the load. c. Calculate the maximum shear. 26 kN 36 kN 16 kN 6 m 3 m A 15 m