Situation 11- The force P of magnitude 850 N is applied to the pedal shown in Figure S03-25M (252). The allowable shearing stress in the pin at C is 40 MPa. mmm 45. Determine the required diameter of pin at C, in mm. A. 4 mm C. 5 mm B. 7 mm D. 6 mm 46. What is the corresponding bearing stress in the pedal at C in MPa. A. 40.93 C. 49.87 B. 45.68 D. 43.58 47. What is the corresponding bearing stress in the bracket support at C in MPa? A. 32.24 C. 30.87 D. 34.69 B. 36.83 75 mm A 125 mm 9 mm 4412 5 mm 5 mm O -300 mm - Figure S03-25M(252) D

Situation 11- The force P of magnitude 850 N is applied to the pedal shown in Figure S03-25M (252). The allowable shearing stress in the pin at C is 40 MPa. mmm 45. Determine the required diameter of pin at C, in mm. A. 4 mm C. 5 mm B. 7 mm D. 6 mm 46. What is the corresponding bearing stress in the pedal at C in MPa. A. 40.93 C. 49.87 B. 45.68 D. 43.58 47. What is the corresponding bearing stress in the bracket support at C in MPa? A. 32.24 C. 30.87 D. 34.69 B. 36.83 75 mm A 125 mm 9 mm 4412 5 mm 5 mm O -300 mm - Figure S03-25M(252) D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The same torque is applied to two tubes with identical metal sheets, determine the ratio of Tdrcle/Tsquare of the shear stresses. Given: r= 11 mm, S = 22 mm, and t 2.67 mm. 32' KA 43 F1 ESC F7 F8 RU Y] U ALT
. Problem 4: The lap joint is connected by 3 20mm - diameter rivets. Assuming that theload P = 50 KN is equally distributed among the 3 rivets, find-The shear stress in each rivet. - The bearing stress between rivet and plate. - The tensile stress in each plate.
The following beam is supported by an aluminum bar at C, a steel bar at B, and a brass bar at D. The distance b is equal to 50 mm. The data is shown in the table:If the maximum rotation that can occur at point A is 0.25 radians clockwise, determine: a. The maximum force P that can be applied. Answ: 28347.97 kNb. The normal stress in the aluminum, steel, and brass bars. Answ: 25 000 MPa, 17500 MPa, 25937.5 MPa
Problem 4: A high-strength steel wire CD is restraining an angle bracket ABC which supports a load P at A. Diameter of wire CD is 1/8 of an inch and the diameter of the pin at B is 1/8 of an inch. Determine the tensile stress in wire CD and the direct shear stress in the pin at B. dw C 4 in. dp B 15° 5 in: View a-a of B P = 200 lb.
For the beam and loading shown, consider the n-n section. (a) Absolute value of shear force in n-n section |V| In kN units, (b) the absolute value of the shear stress at point a of the n-n section |τ| Specify in MPa units. Take the P value of 34 kN and the D value of 17 mm in the question.
Hi can you answer quickly please
i need the answer quickly
A square bar carries a series of loads as shown in Figure P1-47. Compute the stress in each segment of the bar. All loads act along the central axis of 1-47. the bar.
A. Calculate the shear force in the pin at B in pounds. B. Calculate the shear stress in the pin at B in psi.
Part 4a)Determine the reaction (in N) at the hinge at C.b) Determine the diameter of the pin at C in mm.c) Determine the corresponding bearing stress in the pedal at C in MPa.
A solid circular bronze [G = 6,500 ksi] shaft, 6.0 ft long and 1.325 in. in diameter, carries a torque of 90 Ib-ft. For this shaft, determine: (a) the maximum shear stress in the shaft. (b) the magnitude of the angle of twist. Answer: (a) Tmax = psi (b) Ф%3D
12. The bell crank, which is in equilibrium under the forces P and F = 36 kN inclined at θ= 48o, is supported by a pin at D. Determine the shear stress (in MPa) in the pin if it is 21-mm-diameter. P is not equal to F. Round off to two decimal places.