Situation 1 | Consider the figure on the right. A steel plate is used to connect a member to a steel column. 5 - 32 mmø steel bolts are used as fasteners. 1. If P=10 kN determine the average shearing stress on the bolts.** 2. If the allowable shearing stress on the bolts is 60MPA, determine the maximum safe value of P.*

Situation 1 | Consider the figure on the right. A steel plate is used to connect a member to a steel column. 5 - 32 mmø steel bolts are used as fasteners. 1. If P=10 kN determine the average shearing stress on the bolts.** 2. If the allowable shearing stress on the bolts is 60MPA, determine the maximum safe value of P.*

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: (a) Based on the figure, give the minimum and the maximum of the external load, P. (b) Based on the…

A: Double D ring Below shows a Double D ring secured with a Nut and Bolt.

Q: Using Method of Joints, determine the force in BC below. Using Method of Sections, determine the…

A: Calculate the angle α from the given figure.

Q: .B + sodb 30 lb CROSS. SECTION

A: Normal stress: it is defined as the stress that is induced when the member is loaded by axial force.…

Q: The drill is jammed in the wall and is subjected to the torque and force shown in 20 N-m 125 mm σA =…

A: A drill is subjected to torque, we need to find out the normal stress and transverse stress at point…

Q: Consider the T-beam shown in (Figure 1). Take wy 18 kN/m and toy-27 kN/m Figure 200 mm C 200 mm 20…

Q: 1. A solid aluminum shaft 2 in. in diameter is subjected to two torques as shown in the figure.…

A: As per the guidelines only first question should be solved if there is no subparts.

Question

Situation 1 | Consider the figure on the right. A steel
plate is used to connect a member to a steel column. 5
- 32 mmø steel bolts are used as fasteners.
1. If P=10 kN determine the average shearing stress
on the bolts.**
2. If the allowable shearing stress on the bolts is
60MPA, determine the maximum safe value of P.*
Hint: Use the following formula to determine the
centroid.
h
1 (b,? + b2² + b,b2)
3
bị + b2
h(2b; + b2l
3 l b, + b2
CG
b2

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

given data

VIEW

determination of centroid

VIEW

determination of shear stress for each bolt(part1)

VIEW

determination of shear stress for each bolt(part2)

VIEW

determination of safe load for given allowable shear stress

VIEW

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Please show intermediate steps including free body diagrams, equations used, and problem setup so that your approach can be followed.
Quiz1
In the figure shown, assume that a 21.3-mm-diameter rivet joins the plates that are each 118 mm wide. The allowable stresses are 119 MPafor bearing in the plate material and 54 MPa for shearing of the rivet. Determine the minimum thickness of each plate. (Answer must be in millimeters) Round your answer to 2 decimal places.
UPVOTE WILL BE GIVEN. WRITE THE COMPLETE SOLUTIONS LEGIBLY. NO LONG EXPLANATION NEEDED. SOLVE IN 2 DECIMAL PLACES. BOX THE FINAL ANSWERS.
Problem 7 The drill is jammed in the wall and is subjected to the torque and force shown in . Part A Part B A = -215 MPa Correct Part C ((Txy)v) ₁ = 0 MPa A X y Correct a 20 N-m Determine the normal stress at point A on the cross section of drill bit at section a-a. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. ANSWER: 125 mm Determine the transverse stress at point A on the cross section of drill bit at section a-a. Express your answer to three significant figures and include the appropriate units. ANSWER: 400 mm Section a-a 5 mm Determine the torsional stress at point A on the cross section of drill bit at section a-a. Express your answer to three significant figures and include the appropriate units. ANSWER: ((Txz)T) A = 150 N
The shaft is made of L2 tool steel, has a diameter of 40 mm, and is fixed at its ends A and B. It is subjected to the couple shown where F = 2.8 kN. (Figure 1) Figure 400 mm 600 mm 50 mm 50 mm 1 of 1 Determine the maximum shear stress in region AC. Express your answer to three significant figures and include appropriate units. (TAC)max = 61.1 μA Submit Previous Answers Request Answer Part B X Incorrect; Try Again; 9 attempts remaining (TCB)max = MPa Determine the maximum shear stress in region CB. Express your answer to three significant figures and include appropriate units. μA Value ? Units ?
A3-m long steel plate having a cross-section of 25 mm x 300 mm is used as a hanger and subjected to a tensile load of 1070 KN. Poisson's Ratio = 0.25 and E = 200 000 MPa. Compute the total lateral deformation in mm (along the 300 mm side). Express your answers in 4 decimal places.
Please show a detailed solution and explanation including its FBD. Thank you!
The aluminum W 310 x 202 (wide flange) column is subjected to an eccentric axial load P as shown. The maximum compressive stress in the column is given by the so-called secant formula: where --- [¹ + ( √5)] ec o 1+ sec max E ō = P/A = average stress A = 25800 mm² = cross-sectional area of the column e = 85 mm = eccentricity of the load c = 170 mm = half depth of the column r = 142 mm = radius of gyration of the cross section L = 7100 mm = length of the column E = 71 x 10⁹ Pa = modulus of elasticity Determine the maximum load P that the column can carry if the maximum stress is not to exceed 120 × 10^6 Pa. Terminate the computation when Σa < 0.0005%.
Please show full solution, thank you
Subject: Steel design- Bolted Steel Connection - Bolted Subjected to Eccentric Loads *Use NSCP 2015 formula/guide to solve this problem *Use Handwritten