e drill is jammed in the wall and is subjected to the torque and force shown in . rt A JA -215 MPa rt B Correct rt C a 20 N-m 125 mm Determine the normal stress at point A on the cross section of drill bit at section a-a. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. ANSWER: Correct Determine the transverse stress at point A on the cross section of drill bit at section a-a. Express your answer to three significant figures and include the appropriate units. ANSWER: ((Tay)v) A = 0 MPa 400 mm Section a-a -5 mm Determine the torsional stress at point A on the cross section of drill bit at section a-a. Express your answer to three significant figures and include the appropriate units. ANSWER: ((Txz)T) A = 150 N

e drill is jammed in the wall and is subjected to the torque and force shown in . rt A JA -215 MPa rt B Correct rt C a 20 N-m 125 mm Determine the normal stress at point A on the cross section of drill bit at section a-a. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. ANSWER: Correct Determine the transverse stress at point A on the cross section of drill bit at section a-a. Express your answer to three significant figures and include the appropriate units. ANSWER: ((Tay)v) A = 0 MPa 400 mm Section a-a -5 mm Determine the torsional stress at point A on the cross section of drill bit at section a-a. Express your answer to three significant figures and include the appropriate units. ANSWER: ((Txz)T) A = 150 N

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

How do I solve this using Mohr’s Circle
I need the answer quickly
Two shafts are made of the same material. The cross section of shaft A is a square of side b and that of shaft B is a circle of diameter b. Knowing that the shafts are subjected to the same torque, determine the ratio TA/TB of maximum shearing stresses occurring in the shafts. Refer to Table 3.1. -b- -b- ko b A Check my work B The ratio of maximum shearing stresses is TA/TB= 5
Two steel plates are connected by a pair of splice plates with eight bolts as shown. The ultimate strength of the bolts is bolts is 270 MPa. An axial tension load of P = 480 kN is transmitted by the steel plates. If a factor of safety of 1.6 with respect to failure by fracture is specified, determine the minimum acceptable diameter "d" for the bolts. %3D P. splice plate steel steel plate plate (2) (1)
SIMPLE STRESSES 340 mm 3. Two plates are connected by bolts as shown in the figure. Compute the maximum force F that can be applied to the plates. The allowable axial stress of each plate is 150 Мра. The allowable shear stress of each bolt is 50 MPa. The diameter of each bolt is 16 F F 150 mm F F mm. 50 mm 340 mm
1
please answer all the questions with complete solutions and draw a proper free body diagram. Thank you
Pls answer as indian code practice
Question 5 of 15 The plate of thickness, t 5 mm, is loaded with the following stress; o, - 100 MPa, o, - -60 MPa, E- 200 GPa, v = 0.33. If a 160 mm, and b 200 minn, D. ► X A Calculate the change in thickness (mm). Select the correct response:
The assembly consists of two A992 steel bolts AB and EF and an 6061-T6 aluminum rod CD. When the temperature is 30°C, the gap between the rod and rigid member AE is 0.1 mm. Assume BF is also rigid. (Figure 1) Figure 400 mm A B 25 mm 50 mm D 0.1 mm 300 mm E 1 of 1 25 mm Part A Determine the normal stress developed in the bolts if the temperature rises to 180°C. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. of = Submit Part B σ₁ = Submit O HA Value Request Answer Provide Feedback ■μÅ Value Determine the normal stress developed in the rod if the temperature rises to 180°C. Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. Units Request Answer wwwww Units ? wwwww Review ? Next >
42 KN the cross-sectional area of each member is 600 mm² Determine the stress in member EF. Answer in MPa rounded-off to 2 decimal places AddSNUIF ana. 2m A Last saved 4:09:09 PM 1455 ET 2 m Next > Last >
Part A If the required clamping force at the board A is to be 85 N, determine the torque M that must be applied to the handle of the "C" clamp to tighten it down. The single square-threaded screw has a mean radius of 10 mm, a lead of 3 mm, and the coefficient of static friction is u, = 0.35. Express your answer to three significant figures and include the appropriate units. M = 1.1142 Nm O The unit you entered is not recognized. Review a list of acceptable units. No credit lost. Try again. Submit Previous Answers Request Answer Figure 1 of 1 Provide Feedback Next > M O Pearson