Show the steps and calculations to determine one type of fit.  Diameter of ball bearing hole is = 19.945mm

Q: A- a compound gear train shown in D F Figure below all gears are mounted on A E parallel shafts. The…

A: Given data: Speed of gear A, NA = 800 rpm. Number of teeth on gear A, TA = 24. Number of teeth on…

Q: B-A flywheel is used to give up 18 kJ of energy in reducing its speed from 100 rpm to 96 rpm.…

A: Solution:

Q: A solid steel shaft with a diameter of 130 mm must be press-fitted in a journal bearing (Figure 1)…

A:

Q: A disk of mass 10 kg attached rotating above frictionless table nosition (1) The tangential vela

A: In the given problem, we have been provided with two situations  1) At position 1, the disc is…

Q: Determine the permanent elongation of the bar after removal of the load. [Assume elastic, perfectly…

A:

Q: Shaft (250 mm diameter) rotates at 250 rpm inside a sleeve (251 mm diameter) with a constant…

A: Given data diameter of shaft (d) = 250 mm  diameter of sleeve (D) = 251 mm Power required = 2204 W N…

Q: 5/4 Specify the x-, y-, and z-coordinates of the mass center of the quarter-cylindrical shell. 360…

A:

Q: For the following hole and shaft assembly, determine hole and shaft tolerance and type of fit. Hole…

A: Hole      Upper limit of hole =20.025 mm      Lower limit of hole =20.000 Mm Shaft       Upper limit…

Q: 5.17 For the beam and loading shown, determine the maximum normal stress due to bending on a…

A: Bending moment diagram (kN-m)

Q: Rod ABC has a diameter of 30 mm at AB and diameter of 20 mm at BC. the whole rod is subjected to a…

A:

Q: Determine the pressure difference between points C and D. Take the specific weights to be Benzene:…

A: The pressure under hydrostatic condition is the normal force per unit area on the fluid element.…

Q: Define the various types of fits? Also define fits in terms of shaft and hole basis system

A: Fits is defined as a term that is widely used in manufacturing engineering. It is the assembly…

Q: Q2: A, B, C and D are four masses carried by a rotating shaft at radii 100, 125, 200 and 150 mm…

A: Radius of A,B,C and D are 100 mm,125 mm,200 mm and 150 mm Mass 0f A,B,C are 7 kg, 10 kg 5 kg

Q: For the truss shown in Figure The cross sectional area of each member is 1000 mm² Find the stresses…

A:

Q: A research-type submersible with remote TV monitoring capabilities and weighing 35 200 N, was…

A: Given data: The weight of the research-type submersible is, P=35200 N. The the research-type…

Q: The thin-walled tube is subjected to an axial force of 40 kN If the tube contractes 3 mm and its…

A:

Q: If F1 = {100i – 120j +75k} Ib and F2 = {-200i – 250j +100k} Ib, determine the resultant moment %3D…

A:

Q: A cylindrical steel pressure vessel 400 mm in diameter with a wall thickness of 20 mm is subjected…

A: Given data: Diameter of pressure vessel, d = 400 mm. The thickness of the vessel, t = 20 mm.…

Q: 50 +0.012 mm and the hole size are 1. The dimensions for the shaft size are +0.015 50+0.005 +0.000…

A:

Q: A six-cylinder. 5.5-liter Sl engine operates on a four-stroke cycle at 3000 RPM. At this condition,…

A: AS PER COMPANY GUIDELINES, ONLY  3 SUBPART CAN BE SOLVED. FOR SOLUTION OF OTHER SUBPART, KINDLY…

Q: A closed cylindrical container of length 0.6 m and diameter 0.3 m is full of oil of sg = 0.85. It is…

A:

Q: For a No. 7 ball bearing, the New Departure Handbook states that the maximum bore should be 1.3780…

A:

Q: A particle moves along the curve y = x - (x² / 325), where x and y are in ft. If the velocity…

A: Given, y=x-x2325vx=3ft/sax=0(as velocity remain constant)x=15ft Now,…

Q: hree different liquids (A, B, and C) are used in the monometer as shown bellow. 1- Drive an…

A: Given data: The magnitude of pressure P2 = 1.5 bar. The density of methanol, ρA = 0.792 g/cm3. The…

Q: Q2 A steel rod is heated from 25 to 250. Its coefficient of thermal expansion is 10-5/°C and E = 100…

A: Given data: -  The initial temperature of steel rod is T1 = 25 oC. The final temperature of steel…

Q: Q 5 A vertical axis circular cylindrical water storage tank of cross-sectional area A is filled to a…

A: Given Depth h=15 m Radius r=4 m Yield stress σy=240 MPa Factor of safety F.S.=2 γwater=9800 N/m3

Q: Two large fixed parallel planes are 240 mm apart. The space between the surfaces is filled with oil…

A:

Q: A tank is filled with fluid under pressure and the pressure gauge fixed at the top indicates a…

A: Given Data⇒ Tank is filled with fluid under pressure  P=21 KPa The curved surface of the top is…

Q: The structure is designed to support kN load. The structure consists of a boom and rod joined by…

A: Here  are x-component and y-component of reaction force at support A,  are x-component and…

Q: -0.05 m. The dimensions for the shaft size are 020 -0.10 1. mm and the hole size are O20 Find the…

A:

Q: Q 4 A spherical tank for storing gas under pressure is 25 m in diameter and is made of structural…

A:

Limits, Fits, and Tolerances

The maximum or minimum allowable sizes within which the size of component lies are known as limits. The limits are classified into two types: