Show strain gage installation for Uniaxial Loading, Biaxial Loading, Pressure in pipe, Bending and Torque application. State reasons for orientation and insert figures.

Q: The load on square section bar consists of a transverse shear force of 12 kN together with an axial…

A: Given: P=20 kNFt=12 kNσy=260 MPaf=1.8ν=0.28

Q: for a machine part, the following stresses are determined at the most critical point: 0x = 100,0y =…

A:

Q: Sketch Mohr's circles for Uniaxial tension Hydrostatic compression Pure shear.

A:

Q: 1 Eaxial Ehoop 91 92

A:

Q: Example: the conical valve of an I.C. engine is 60mm in dimeter and is subjected to a maximum gas…

A: Step 1: Given data: D=60mm Pmax=4Mpa σb​=46Mpa K=0.42 θ=30° Part 1: Thickness will be calculated by…

Q: 2. A light helical spring is fabricated by wrapping %-in diameter wire around a forming cylinder 10…

A: Given data: τmax=18 ksid=3/4 inD=10 inR=D2=5 inG=12×106 psiδ=3.5 in Need to determine the number of…

Q: The figure shows an anvil for an impact hammer held in a fixture by a circular pin. If the force is…

A:

Q: = = 2. The bending stresses on an element are: om = 25,00 psi or= 21,667 psi. There is a stress…

A:

Q: = 2. The bending stresses on an element are: om = 25,00 psi or= 21,667 psi. There is a stress raiser…

A: ASME ellipse criterion:- ASME ellipse criterion is a theory of failure used to design component…

Q: Whoop- ニフ P:?

A:

Q: Q1: Find a relation between true strain () and reduction in area (r)?

A:

Q: 2. The bending stresses on an element are: om = 25,00 psi or= 21,667 psi. There is a stress raiser…

A:

Q: Introduction to stress analysis Problem: Calculate the critical design loads applied to the piston…

A: Piston is a reciprocating part of an internal combustion engine which reciprocate with in the…

Q: A rod tensile test of Lo = 50mm, do = 10mm was subjected. FA = 21000N, E = 210 GPa. What was the…

A: P=FA=21,000 N=21 kNE=210 GPa=210×109 Pa=210×106 kPaL0=50 mm=0.05 md0=10 mm==0.01 m

Q: 14. For O 127mm S-135 drill pipe, it has the tensile load under the yield strength of 3167.43kN,…

A: Static load is defined as the load which is applied gradually.  A part from increasing from zero to…

Q: The principal stresses are given as 20, 0 and 30 respectively, what is the shear stress? Selected…

A: To find: The shear stress. Given: The principle stress is σ1=20, σ2=0 and σ3=30. Concept used: The…

Q: Hi, the diameter is 10 mm in my problem, not 15 mm.

A:

Q: The central plates a in Fig.12 of the text are 9/16 in. thick and 9 in. wide. The diameter of the…

A:

Q: During drawing process, using the Ao=5mm2, Af =4 mm2, K=200 MPa and n = 0.20, the average flow…

A:

Q: 1. A cold-drawn AISI 1015 steel tube is 300 mm OD by 200 mm ID and is to be subjected to an external…

A: Given data - Outer diameter - 300 mm Internal diameter - 200 mm Yield strength = 600 Mpa It is asked…

Q: 8. What temperature will the rails just touched if steel railroad is 10 m long are laid with…

A: Dear student,                    According to the guidelines I am allowed to answer only one problem…

Q: The cylinder head of a 10”x18” refrigerant compressor is attached by 10 stud bolts made of SAE grade…

A:

Q: PLS MADE A FBD DIAGRAM !!!!! easy!!!!!! there is a rubber mat circled in yellow that is non slip and…

A: It is asked to calculate the reactions in the rubber mat.

Q: A fatigue cycle has a minimum stress of 21 ksi and a maximum stress of 53 ksi. The R- Ratio is: O…

A:

Q: Q3/A/ a steel slab is upset forged from: (50mm×200mm×100mm) to (25mm × 200mm × 200mm). If the…

A:

Q: If diameter of solid shaft is halved and torque being transmitted is doubled, what will be change in…

A: Shear stress (τ) in the shaft of diameter (d) due to torque (T) can be given by, τ = 16Tπ d3…

Q: 1) A set of pipes are available with 50-mm inner-diameter and varying outer-diameters from 51 mm to…

A: Given that, Inner diameter of pipe, Di=50 mm,Outer diameter=DoPower available from shaft, P=110…

Q: In a triaxial compression test, for drained condition the confining pressure is 200 kPaand deviator…

A: Triaxial compression test, Calculate the net shear stress at the initial condition.

Q: (14) The figure shows a formed round-wire cantilever spring (Sut = 188.1 kpsi) subjected to a…

A: Given that, Sut=188.1 kpsi,Fmax=30 lbf,Fmin=15 lbf,…

Q: What should be the nearest standard diameter of a steel bolt (in 1/8th of an inch increment in…

A:

Q: for a machine part, the following stresses are determined at the most critical point: 0x = 100,0y =…

A:

Q: 12-0" TYP 10 NZ 12'0" TYP Use the diagram shown above. Given P-300 # Calculate the magnitude of the…

A: To Find : The magnitude of internal force in member 3 Given : The load  p is The free body diagram…

Q: Make dimensioning for the figure whose stress values are given below. a=?, b=?, h=? (column stress…

A:

Q: A power transmission shaft is to carry a steady 30 horsepower while rotating at 1000 rpm. Specify a…

A:

Q: Given data K=200 GPa Poissons ratio=0.34 Determine Youngs modulus

A: Given data : The value of Bulk modulus =K K=200 GPa The value of Poisson's ratio=μ μ=0.34

Q: Write the nature of work done by an elongated spring?

A: The elongation produced in an ideal spring is directly proportional to the spring force F=−kx.

Q: Part 1 is as follows: al Diameter (mm) Tolerance (mт- 6 - 7.5 + 0.045 8 –10 + 0.050 a diameter wire…

A: To Find :  The mean and standard deviation of the population of torsional shear stress  Given : The…

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.