Calculate the magnitude of the tension T and the angle @ for which the eye bolt will be under a resultant downward force of 15.0 kN. Assume F = 6.5 kN, P = 7.3 kN, = 24° The tolerance is ± 1 in the 3rd significant digit. T= T 0= i KN F P

Q: please solve and explain using values below

A: Detailed step by step solution is given below, still if you have any query please feel free to…

Q: Q // If the value of the highest load we get from the tensile test of a wrought iron model with a…

A:

Q: 1 Eaxial Ehoop 91 92

A:

Q: A-2 Determine the vertical displacement of joint C.Assume e members are pin connected at their end…

A: A = 200 mm²   E = 200 Gpa

Q: Calculate the range for the stress of the load measures 100 lbs. and the load cell used has an error…

A: Calculated the range of stress of the load .

Q: Using loop closure method, solve the instantaneous acceleration of the slider P (in the diagonal…

A:

Q: Using the sample set of readings provided for Experiment 1 and taking the Young's Modulus of steel…

A: i hope its helpfull.thank you.

Q: 1. Determine the diameter size of rods AB, BC and C if ay = 3600 MPa and the safety factor SF= 2.…

A: Determine the diameter size of rods AB, BC and CA, if Yield stress = Sy = 3600 MPa and the safety…

Q: Material A and Material B are tested in tension Material A is loaded to the proportional limit which…

A: Since we know that, the resilience of the body is the total energy absorbed by it before fracture…

Q: If the roller at B can withstand a max load of 3 kN, determine the largest magnitude, F, of the…

A: Given: max load at roller B = 3kN now we can evaluate force F by using simple equilibrium…

Q: Set P 8 kN and P 16 kN (Figure 1) Figure E D 4 Part E Determine the force in member BE, and state if…

A:

Q: Please write it out. I don’t like the computer typed answers. Need help on all questions. Please…

A:

Q: The length of the cable segment AB is 10 ft (Eigure 1) The angle a = 30° ▼ Part A What force T is…

A: The length of AB is .The angle is The weight of crate is

Q: 3-132 Steel 0 1.002/1.003 Steel 1.001/1.002 2.00

A:

Q: A force P of magnitude 950 N is applied to the pedal shown. NOTE: This is a multi-part question.…

A: The value of force P is 950 N The thickness of the support is t=5 mm

Q: Quiz ch-2 Strain rosette readings are made at a critical point on the free surface in a structural…

A: Strain rosette readings are made at a critical point on the free surface in a structural steel…

Q: An engineer is designing a cylindrical steel pin that must fit into a bronze bushing for a…

A: Limits, Fits, and Tolerances  deal with the dimensional accuracy and operational interplay of mating…

Q: The wire-mass system shown is constructed using 6061-T6 aluminum wire. Determine the minimum…

A:

Q: Bracket BCD is supported by a hinge at C and a cable at B, as shown below. Given the forces P=288 N…

A:

Q: The overhang beam is supported by a pin at point A and a roller at point B. A distributed load is…

A:

Q: Please draw a FBD only for the circled yellow part known as a rubber base plate :) I don’t want the…

A:

Q: Two metal bars are fastened together at the bolted flange connection shown. There are 2 total bolts…

A:

Q: Please solve the problem with a neat paper sheet. The length AB for the lug wrench shown below is 12…

A:

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.