Show complete solution and 3 decimal places for the final answer. Asap thanks!  A cube container with a dimension of 3m on each side is 60% full of water (density=1000kg/m^3). The cable elevator lifted it upwards with 25kN. Estimate the resulting pressure at the bottom of the tank in kilo Pascals.

Q: 1. Find the height of the water in the figure shown neglect effect of air. PB = 0.2 ke/cm² PA =…

A: Given data in question  Pressure at point A and B Depths Specific gravity To find out  Value of H…

Q: The inclined pipe shown in the figure is used to carry oil (p = 900 kg/m³, μ = 9x10-3 Pa.s) The pipe…

A: Solution: Given: ρ=900 kg/m3 μ=9×10-3Pas D = 20 cm =0.2 m L = 300 m V = 3 m/s

Q: minutes

A:

Q: The resultant vertical component of force of water per meter width of gate will be

A:

Q: Three piezometers are attached to a tank of water subjected to a positive gage air pressure, as…

A:

Q: Part A Determine the maximum pressure in the system shown. Express your answers in kilopascals using…

A: The tank system is shown in figure:

Q: An open tar ank conta от и OT Oll (s=0.75). Calculate the pressure at the bottom of the tank.

A: given water depth, Hw = 5m  Oil depth, Ho = 2m  specific gravity of oil = 0.75,  Required: Pressure…

Q: A swimming pool is 6 feet deep at the deep end. It is 10 by 16 feet at the top and 10 by 4 feet at…

A: Given that: Density of water, γw = 62.4 lb/ft3                   We know that pressure at a depth of…

Q: Oil of specific gravity 0.80 is being pumped. A pressure gage located downstream of the pump reads…

A:

Q: AE 10W-30 oil flows through the 125-mm-diameter pipe hown in (Eigure 1) with an average velocity of…

A: Diameter of pipe, The velocity of flow, length of a section of pipe, = 10mThe density of oil =…

Q: Please answer the following question in the picture please, show all of your work, and explain each…

A: Detailed step by step solution is given below, still if you have any query please feel free to…

Q: EXAMPLE 10.4. The three pipes in figure are cast iron with characteristics as shown in table. The…

A:

Q: SAE 10W-30 oil flows through the 125-1 (Eigure 1) with an average velocity of 1. Figure

A:

Q: Given: A vertical cylindrical tank is 10m high and 7m in diameter. It is two thirds full of water…

A:

Q: Problem 5 Determine the gage pressure at the center of pipe A (marked by +) in both psi and kPa.…

A: Determine the gage pressure at the center of pipe A (marked by +) in both psi and kPa.

Q: 1. Consider a tanker truck as shown in the figure. The truck accelerates 4 m/s2. It is fully filled…

A:

Q: Moving Question 37 A pressure gage 10.82 m. above the bottom of a tank containing a liquid reads…

A:

Q: empt in Progress The homogeneous gate shown in the figure below consists of one quarter of a…

A:

Q: Calculate the fluid force on one side of a semicircular plate of radius 12 ft that rests vertically…

A:

Q: A plunger (54 mm Ø and 0.5 m long) is moving through a horizontal cylinder (60 mm Ø)  containing oil…

A:

Q: A vertical surface 2.00m square has its upper edge horizontal and on the water surface. Determine…

A: Hydrostatic forces are the resultant force caused by the pressure loading of a liquid acting on…

Q: M1 U5: Use the general solution in determining the total hydrostatic force acting on the submerged…

A:

Q: Situation 1 - The pressure on a closed tank reads 58.86 kPa. What is the equivalent height, in…

A:

Q: total pressure force on the gate and the distance between the center of pressure and the centroid…

A: Case 1, when 3ft x 3ft gate is vertically downward from the surface. Case 2, when 3ft x 3ft gate is…

Q: 6. What is the unit of pressure gradient? a) Pa/m b) Nm c) Pa d) N/m

A:

Q: Fluid mechanics, I need solutions in 15 minutes please.

A:

Q: 825 mm 1. If the water rises to 150 mm above the bottom of the door, calculate the hydrostatic force…

A:

Q: Determine the location in m of the total hydrostatic force from the bottom of the gate acting on the…

A: Given data: h1=0.9 m h1=1.6 m h1=3.9 m Width of the gate, b= m depth of the gate, d=5 m Angle θ=60°…

Q: Calculate the pressure at a point 337 mm below the surface of the mercury in a vessel. Express the…

A:

Q: . Calculate the hydrostatic pressure at A (inside of the water tank) in unit of lbf/ft².

A: ##Determination of Hydrostatic Pressure at A (inside water Tank) in lbf/ft2 #

Q: The rate of flow of water entering a pipe is 100kg/min at a temperature of 100 °C and pressure of 2…

A: Given: Mass flow rate, m = 100 kg/min Temperature, T = 100°C Pressure, P = 2 bar                   =…

Q: Each of the blocks shown in figure (9.14) has mass 1 kg. The rear block moves with a speed of 2 m/s…

A:

Q: Refer to the given figure. Given: a = 42cm, b= 15cm, and c= 34cm Water a C 40 cm Gate Unknown liquid…

A:

Q: f the pressure gage shown in the figure indicates a pressure of 6.5 x 10 N/m2 (6.5 bar) what are the…

A: Calculate the pressure at point B as follows: Starting from pressure gauge to the right side top of…

Q: 2. A box of 45ON is lying in an inclined plane with angle of 35 degrees. If the applied load to move…

A: Usually, movement can be defined as, Change speed, Change where you are going. It is easy to see…

Q: the spool has a larger radius ?=0,17 and an inner radius ?=0,13, and it has a coiled rope. Block C…

A:

Q: a A -Во — b D

A:

Q: Formulate the expression for calculating the pressure rise in elastic pipe due to sudden closure of…

A: A water hammer is  high pressure shockwave which is generated in a pipe when valves are suddenly…

Q: Refer to the given figure. Given: a = 36cm, b = 24cm, and c = 29cm Water ← b с Į 40 cm Gate Unknown…

A: use simple method  just find force by individual fluid  and make net force  zero on the gate

Q: Smooth pipe: d=50mm P1 1 10 m I 40m->> 20m 80 m Open jet

A:

Dimensional homogeneity

The term dimensional homogeneity means that in an equation, the dimensions of each term on both sides are equal, which means the dimensions of the left-hand side (LHS) of an equation are similar to the dimensions of the right-hand side (RHS). For a dimensionally homogeneous equation, the powers of fundamental dimensions will be identical on both sides of the equation.