A vertical surface 2.00m square has its upper edge horizontal and on the water surface. Determine the hydrostatic force on the surface. Calculate the depth of the center of pressure from the bottom of the surface. Answer the situations with complete solutions. Write your final answer in two decimal places. Please use the correct unit and box the final answer thank you

Q: Calculate the pressure and speed of water at points b and c as shown.

A: ASKED: To determine the pressure and speed of water at points B and C.   Given, Pressure at A (PA) =…

Q: Solve the following problem. Show necessary illustrations. A vat is filled with oil with a specific…

A:

Q: tank with 1m in diameter and 2 meters in height is supplied with fresh water from the lake.  Find…

A:

Q: Problem 2 The containers A and B, shown on the figure, are filled HO with water, with density Pwater…

A:

Q: . Find the approximate height of water upstream of the dam or the headwater in meters, such that an…

A: Thank you for the question . As per honour code we will answer the first question since exact one…

Q: 1. Water at 41 "C flows through an inclined plane. Determine the velocity and direction of the flow…

A:

Q: What is the total hydrostatic force on the conical stopper shown below? Veone = Tr²h where r is…

A: please find attached solution below

Q: Three piezometers are attached to a tank of water subjected to a positive gage air pressure, as…

A:

Q: (a) Resultant force on the wall of the tank due to the fluids? (b) Moment caused by the fluids along…

A: Given:- Depth of the water  = 1.5m            The thickness of the oil layer = 0.5 m            The…

Q: Air h1=? h2=? h3=? F cg, 60°

A:

Q: Hydrostatic Pressure Lab 0mm 50g 46mm 100g 67mm 150g 84mm 200g 99mm 250g 114mm 300g…

A: ⇒ For 2nd reading         Depth = H = 46mm = 0.046 m          Mass = 600 g = 0.1 kg      Area of…

Q: 1. Atmospheric pressure is about 80 kPa (absolute). Water pressure at the base of a water tower is…

A: In this question I  have to question but according to our guidelines we can answer only one…

Q: C• Air Air 3ft 4ft B Air 5ft 6ft Water 2 ft

A:

Q: Part A Determine the maximum pressure in the system shown. Express your answers in kilopascals using…

A: The tank system is shown in figure:

Q: 4 Determine the absolute pressure at A in kPa if the atmospheric pressure is 101.325 kPa. 92.876…

A: Figure is shown in the question

Q: 2 A rectangular gate AB hinged at A has a width of 2.0 m perpendicular to the paper and has…

A: Given, b= 2m unit weight of water=9.80 kN/m3 To determine, Magnitude of hydrostatic force in kN.

Q: A nozzle discharges 2 cfs with a velocity of 50 ft/sec. The nozzle is inclined downward so that as…

A:

Q: A3 m'square plate is immersed vertically in water such that the two edges of the squa: are…

A:

Q: Identify the type of manometer in the following figures and then compute for the pressures. Use Grid…

A: Case 1: U-Tube Differential Manometer: Consider the grid at the interface of water and mercury.…

Q: You have a pipe with an inside diameter of 3.48 in. and roughness 0.00032 in. A fluid with specific…

A:

Q: A differential manometer is connected at the two points B and C in of two pipes as shown in Figure…

A: Pressure at point B (Pb)=200kPa Difference in mercury level inside the U tube manometer (h)=30cm…

Q: How do you calculate the pressure at the bottom of a column made of rock? The column is cylindrical…

A: Below procedure is a adopted

Q: Given: A vertical cylindrical tank is 10m high and 7m in diameter. It is two thirds full of water…

A:

Q: For a capillary tube with a radius of 1 mm, compute the following: (1) capillar in the tube in mm;…

A: Radius of capillary tube =1mm To find capillary rise, force and weight of water due to surface…

Q: The internal diameter of a tube is 0.1 mm. What will be the maximum capillary rise when it is held…

A:

Q: CLW3.8 Problem • A manometer is used to measure the pressure of a gas in a tank. The fluid used has…

A:

Q: Archimedes® Principle A spherical buoy has a radius of I m and a density one-fourth that of…

A:

Q: The tank shown contains air, oil, and water. Gage A reads 100 kPa and Gage C reads 16.872 kPa more…

A:

Q: Please

A:

Q: M1 U5: Use the general solution in determining the total hydrostatic force acting on the submerged…

A:

Q: Determine the force needed to raise the water to a height 5 m above the free surface. What would…

A:

Q: Q9: For the shown figure, what is the difference in pressure between points A, B? S.9. = 0.92 water…

A: To find pressure difference between point A and B

Q: Water is flowing through a venturimeter shown. The difference in pressure between A (D = 5cm) and B…

A:

Q: Water is flowing through a pipe 1/3 ft. inside diameter into a pipe 1'' in diameter at a rate of…

A: Given: P1 = 275.8 KPa  Q= 12.62 lps  D1= 1/3 ft D2 = 1inch Required : P2

Q: 16. Calculate the pressure, in kPa, at A, B, C, and D.

A:

Q: Please help with solving

A:

Q: 2.Find the surface tension in N/m in a soap bubble of 30 mm diameter when the inside pressure is…

A:

Q: Find the pressure in the pipe.

A:

Dimensional homogeneity

The term dimensional homogeneity means that in an equation, the dimensions of each term on both sides are equal, which means the dimensions of the left-hand side (LHS) of an equation are similar to the dimensions of the right-hand side (RHS). For a dimensionally homogeneous equation, the powers of fundamental dimensions will be identical on both sides of the equation.